Vital Home Systems LLC 1060 Benutzerhandbuch
P a g e
| 4
© 2015 - 2016 Vital Home Systems, LLC
NOTE! You may only connect sensors and VC100
Valve controllers to the Wireless Control Panel with
the Vital Home Systems Windows PC Software.
Valve controllers to the Wireless Control Panel with
the Vital Home Systems Windows PC Software.
To Enter Programming
Mode
Step 1. With the Wireless Control Panel in Normal
Mode, press “Set” key
Step 2: Press “#” Key
Step 3: Enter Pin Code
Step 3: Enter Pin Code
The Pin code consists of a 4-digit number.
Factory default is “0000”.
Factory default is “0000”.
Step 4: Press “Set” key. A long beep is emitted and
Power LED lights ON Red.
NOTE:
Under Program Mode, a key-press interval
of five (5) seconds is allowed; the process
will abort automatically if the time is
exceeded, or incorrect entry is made. A
quick four (4)-beep sound will be emitted,
indicating Program exit Mode and return to
Normal Mode.
will abort automatically if the time is
exceeded, or incorrect entry is made. A
quick four (4)-beep sound will be emitted,
indicating Program exit Mode and return to
Normal Mode.
Once in Program Mode, if a key is not
pressed for 30 minutes. The Wireless
Control Panel will sound five (5) quick-
beeps, then automatically exit Program
Mode and return to Normal Mode.
Control Panel will sound five (5) quick-
beeps, then automatically exit Program
Mode and return to Normal Mode.
To enter Program Mode, return to Step 1.
You may press “CLR” key anytime to exit
You may press “CLR” key anytime to exit
Program Mode and return to Normal Mode.
Under Programming Mode, you may perform the
following settings:
following settings:
Open or Close the VC100 Valve Controller
Storing, change, or remove Telephone
Numbers
Numbers
Disable or Enable auto water shut
automatic valve operations
automatic valve operations
Range Testing for valves and sensors
Storing Phone Numbers
Step 1: With Wireless Control Panel already set to
Programming Mode, press “SET” key.
Step 2: Select your Dialling Priority Order Number 1
through 6. Then press the “#” key.
NOTE:
A maximum of five (5)
CELL PHONE
NUMBERS ONLY
numbers may be stored in
priority order. You may store less than five
numbers.
numbers.
1, 2, 3, 4, and 5 represent the priority
number of the five telephone numbers
respectively.
respectively.
The Wireless Control Panel will
automatically dial in sequence of the stored
cell phone numbers.
cell phone numbers.
Step 3: Key in phone number (maximum 20 digits),
then follow by the “SET” key to complete entry.
NOTE:
then follow by the “SET” key to complete entry.
NOTE:
The “*” may be used to delay dialing for
three (3) seconds. If more delay time is
required, pressing an additional “*” will
allow an additional three second delay
time. You may press “*” as often as
required.
required, pressing an additional “*” will
allow an additional three second delay
time. You may press “*” as often as
required.
Changing Phone Numbers
To change the telephone numbers, follow the steps
in Storing Telephone Numbers described in previous
section, then enter the new telephone numbers.
This will override the numbers previously
programmed.
in Storing Telephone Numbers described in previous
section, then enter the new telephone numbers.
This will override the numbers previously
programmed.
Clear Phone Numbers
To delete the telephone numbers, follow the steps
as in Storing Telephone Numbers described in
previous section and press “SET” without entering
any new phone numbers.
as in Storing Telephone Numbers described in
previous section and press “SET” without entering
any new phone numbers.
SET + 1~6 + SET
Successful deletion is indicated by a long beep,
followed by Power LED Red lights ON.
NOTE:
followed by Power LED Red lights ON.
NOTE:
For Storing, Changing or Removing
telephone numbers, a key-press interval of
five (5) seconds allowed.
If time is exceeded, or an entry is made in
error, the unit will automatically abort the
process and emit quick four (4) beeps,
indicating return to Program Mode.
five (5) seconds allowed.
If time is exceeded, or an entry is made in
error, the unit will automatically abort the
process and emit quick four (4) beeps,
indicating return to Program Mode.
To exit Programming Mode and return to
Normal Mode, press “CLR” key.
Range Testing
Step 1: With the Wireless Control Panel in
Programming Mode, press “Test” key followed
by “8 then 0 then Set.”
The Power LED Red will flash, indicating that it
has entered Range-Test Mode.
by “8 then 0 then Set.”
The Power LED Red will flash, indicating that it
has entered Range-Test Mode.
Step 2: Press Sensor Test button. The Power LED
Red flashes ON for one (1) second then a long
beep will sound, indicating that signal has been
successfully received at this distance range.
beep will sound, indicating that signal has been
successfully received at this distance range.