ZONITH A/S BTBLE-IDBDG Benutzerhandbuch
OPERATIONAL USE
Back side of the ZONITH Bluetooth LE ID Badge™
Front side of the ZONITH Bluetooth LE ID Badge™
CHARGING AND BATTERY
Charging of the ZONITH Bluetooth LE ID Badge™ is done via the Micro
B USB connector. Use a standard USB connection or charger
supporting: 5V - 150mA.
B USB connector. Use a standard USB connection or charger
supporting: 5V - 150mA.
During charging, the LED shows a solid Blue color. When the badge is
fully charged, the LED either turns off or fall back to normal state.
fully charged, the LED either turns off or fall back to normal state.
If during operation the battery level goes low the LED starts flashing
RED every 4 seconds to indicate the badge need to be recharged.
RED every 4 seconds to indicate the badge need to be recharged.
With a fully charged battery, the expected operational time is above 3
months.
months.
POWER ON AND OFF
To power ON the ZONITH Bluetooth LE ID Badge™ you have to press
and hold the POWER button for 2 seconds. When powered ON the LED
will flash blue every 4 seconds (normal operation).
and hold the POWER button for 2 seconds. When powered ON the LED
will flash blue every 4 seconds (normal operation).
To turn OFF the device you have to press and hold the POWER button
for 5 seconds. When powered OFF the LED turns off.
for 5 seconds. When powered OFF the LED turns off.
ALARM BUTTON
The ZONITH Bluetooth LE ID Badge™ supports two types of alarms or
events from the ALARM button at the back, defined by a double click and
a long button press.
events from the ALARM button at the back, defined by a double click and
a long button press.
Name
Double click
Two “click and release” of the
button in less than 1 second
button in less than 1 second
Long button press
Press and hold the button in at
least 2 seconds
least 2 seconds
The action that is initiated based on the two types of alarms are defined
in the ZONITH Alarm Control System (ACS).
in the ZONITH Alarm Control System (ACS).
The ZONITH Bluetooth LE ID Badge™ stays in any of the alarm states
for 2 minutes. If the user performed the double click the LED will flash
red every second. If the user performed the long button press the LED
will be solid red. The long button press override the LED behavior so that
if long button press is performed shortly after double click the LED will be
solid RED. When the ZONITH Bluetooth LE ID Badge™ leaves the
alarm state the LED will switch back to a flashing blue light every 4
seconds.
for 2 minutes. If the user performed the double click the LED will flash
red every second. If the user performed the long button press the LED
will be solid red. The long button press override the LED behavior so that
if long button press is performed shortly after double click the LED will be
solid RED. When the ZONITH Bluetooth LE ID Badge™ leaves the
alarm state the LED will switch back to a flashing blue light every 4
seconds.
If the user wish to leave the alarm state faster than the 2 minutes the
ZONITH Bluetooth LE ID Badge™ has to be powered off and powered
on again.
ZONITH Bluetooth LE ID Badge™ has to be powered off and powered
on again.
The ALARM button is located in the center on the back side of the unit.
The alarm button is marked with a 2 mm. circle around it so that the
users easily can find it without looking at the badge itself.
The alarm button is marked with a 2 mm. circle around it so that the
users easily can find it without looking at the badge itself.
LED
The LED is used to indicate the state of the ZONITH Bluetooth LE ID
Badge™. The different modes it can display are:
Badge™. The different modes it can display are:
LED
Function
Turned off
The badge is turned off. This is also the
situation if the badge is connected to a charger
and the charging is complete.
situation if the badge is connected to a charger
and the charging is complete.
Solid blue
The badge is being charged.
Flashing blue (4
seconds)
seconds)
The badge is turned on and in normal
operation.
operation.
Solid red
The badge is in long button alarm state.
Flashing red (1
second)
second)
The badge is in double click alarm state
NOTE: If long button press is also active then it
will show solid red.
NOTE: If long button press is also active then it
will show solid red.
Flashing red (4
seconds)
seconds)
The badge is low on battery and needs re-
charging.
charging.
It is possible to turn off the LED manually while the badge continues to
operate normally.
operate normally.
To turn off the LED, press and hold the POWER button for 0.5 seconds.
To turn the LED on again press and hold the POWER button for 0.5
seconds.
To turn the LED on again press and hold the POWER button for 0.5
seconds.
COPYRIGHT AND TRADEMARK INFO
© 2018 ZONITH A/S. ZONITH, The ZONITH logo and “ZONITH Bluetooth LE ID
Badge” is a trademark of ZONITH A/S. All rights reserved.
Badge” is a trademark of ZONITH A/S. All rights reserved.
ALARM button
Power button
LED
Insert ID or access card here
Handles for clasp
Identity card
place holder
or neck strap