3M Low power connector ATT.CALC.CROSS_SECTION_FLEXIBLE: 0.3-0.56 mm² ATT.CALC.CROSS_SECTION_RIGID: 0.3-0.56 mm² Number of p 37303-2124-000 FL Datenbogen
Produktcode
37303-2124-000 FL
Product Information
Mini Clamp Wiremount Socket Connector
3M Deutschland GmbH
Tel.: 02131 / 14 2040
3 - 8
February 2004
Electronic Solutions
Fax.: 02131 / 14 2065
Carl-Schurz-Straße 1
E-Mail: 3minterconnects.de
41453 Neuss
Example 2) At the time of combination with UL1007, AWG24 (11/0.16), finish contour f 1.49, Heat-resistant
vinyl isolation outer bark electric wire made in Showa Electric Wire & Cable Co.,Ltd. and 37104-3163-000
FL made in 3M
An average of 46.6 N (the fewest 35.9N).
vinyl isolation outer bark electric wire made in Showa Electric Wire & Cable Co.,Ltd. and 37104-3163-000
FL made in 3M
An average of 46.6 N (the fewest 35.9N).
Example 3) At the time of combination with IR-1, 0.14SQ (7/0.16), finish contour f 1.34, Cure PE isolation
outer bark electric wire made in Showa Electric Wire & Cable Co.,Ltd. and 37104-3163-000 FL made in 3M
An average of 23.0N (the fewest 18.8N).
outer bark electric wire made in Showa Electric Wire & Cable Co.,Ltd. and 37104-3163-000 FL made in 3M
An average of 23.0N (the fewest 18.8N).
Quality Performance
Unit Characteristics
TEST
DESCRIPTION
REQUIREMENT
TEST CONDITION
RELATED STD.
Reference
Dielectric with-
standing voltage
standing voltage
No appearance of arcing
and break down.
Leak current : 1mA max
and break down.
Leak current : 1mA max
Impressed voltage is AC 1000V rms between
two adjacent contacts for 1 minute.
two adjacent contacts for 1 minute.
MIL-202F-301
Insulation
Resistance
Resistance
1000M min
Impressed voltage is DC500V between two
adjacent contacts for 1minute.
adjacent contacts for 1minute.
MIL-202F-302
Mating characteristic
It depends on combination with the Mini-Clamp connector series 371XX series
TEST
DESCRIPTION
REQUIREMENT
TEST CONDITION
RELATED STD.
Reference
Insertion &
Withdrawal Force
(Initial)
Withdrawal Force
(Initial)
Insertion 2N/pin max.
Withdrawal 0.5N/pin
min.
Withdrawal 0.5N/pin
min.
Tensile speed : 5mm/min. Spec. value is
estimated by one contact pin.
estimated by one contact pin.
Retention Force of
Latch
Latch
58.8N min
Tensile speed: 25mm/min.
Durability
Electrical properties
shall be stable after test
shall be stable after test
Insertion & Withdrawel 300 times. (Except
Latch Mechanism)
Latch Mechanism)
Vibration
Electrical properties
shall be stable after
test. Discontinuity
1 sec. max
shall be stable after
test. Discontinuity
1 sec. max
Tested during vibration test together (See
table 1)
table 1)
MIL-202F-201
A
Shock
Electrical properties
shall be stable after
test. Discontinuity
1 sec. max
shall be stable after
test. Discontinuity
1 sec. max
50G , 11 msec , 3 cycles, 3 directions
(X,Y,Z)
(X,Y,Z)
MIL-202F-213
B
Electrical Specifications
TEST
DESCRIPTION
REQUIREMENT
TEST CONDITION
RELATED STD.
Reference
Electrical
Continuity
Continuity
Electrical properties shall
be state under test.
Discontinuity 1
be state under test.
Discontinuity 1
sec max
Tested during Vibration test together
Refer TABLE-2
Contact Resistance
The initial readings are in
milli-ohms. 20m
milli-ohms. 20m
max
The low-signal level contact resistance shall be
tested with circuit current of 1mA and open
circuit voltage of 20 mV maximum. The
termination resistance includes bulk resistance
of contact, and resistance of solder joints of
connectors to circuit boards.
tested with circuit current of 1mA and open
circuit voltage of 20 mV maximum. The
termination resistance includes bulk resistance
of contact, and resistance of solder joints of
connectors to circuit boards.