Crydom DRA-CN240A24 Din Rail Mount Electronic Power Relay DRA-CN240A24 Current load 2 A Switching voltage 24 - 280 Vac DRA-CN240A24 Merkblatt
Produktcode
DRA-CN240A24
DRA-CN Assemblies
DIN Rail mountable assemblies of Solid State Relays and Sockets
FEATURES
The DRA-CN assemblies provide a convenient and easy way to select and use Crydom CN series Solid
State Relays on a standard 35mm DIN rail. For additional information visit www.crydom.com.
State Relays on a standard 35mm DIN rail. For additional information visit www.crydom.com.
Factory assembled ready to use assemblies for AC and DC input
24VDC @ 3.5A, 48VDC @ 100mA and 240VAC @ 2A Operating Voltage Rating
6.2mm wide socket
LED input status indicator
Socket clip fits all standard 35mm DIN rails
24VDC @ 3.5A, 48VDC @ 100mA and 240VAC @ 2A Operating Voltage Rating
6.2mm wide socket
LED input status indicator
Socket clip fits all standard 35mm DIN rails
DERATING CURVES
DRA-CN
024D
Series
Load Voltage
024D: 24 VDC, 3.5 A
048D: 48 VDC, 0.1 A
240A: 240 VAC, 2 A
024D: 24 VDC, 3.5 A
048D: 48 VDC, 0.1 A
240A: 240 VAC, 2 A
Switching Mode
Blank: Zero Cross Turn-On
(AC Output Only)
R: Random Turn-On
Blank: Zero Cross Turn-On
(AC Output Only)
R: Random Turn-On
24
R
Assembly Input Voltage
05: 05 VDC
24: 24 VDC
120: 120 V AC/DC
240: 240 V AC/DC
05: 05 VDC
24: 24 VDC
120: 120 V AC/DC
240: 240 V AC/DC
PART NUMBER NOMENCLATURE
A
INSTALLATION INSTRUCTIONS
Mount the assembly on the DIN rail
Wire the socket to the control side. AWG #24-14 Solid, AWG #24-14 Stranded. (0.14-2.5mm2)
Wire the socket to the load side. AWG #24-14 Solid, AWG #24-14 Stranded. (0.14-2.5mm2)
If multiple units are installed be sure to follow derating curves for assemblies
Wire the socket to the control side. AWG #24-14 Solid, AWG #24-14 Stranded. (0.14-2.5mm2)
Wire the socket to the load side. AWG #24-14 Solid, AWG #24-14 Stranded. (0.14-2.5mm2)
If multiple units are installed be sure to follow derating curves for assemblies
Please read all installation instructions before using the assemblies.
Assembly part number is marked on the opposite side of the socket from the socket's labeling.
WIRING DIAGRAM
For DRA-CN assembly wiring diagram see DRSCN wiring diagram shown in installation sheet
(reverse side of this sheet).
(reverse side of this sheet).
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA /
警告
RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être chauds. Laisser le produit
refroidir avant de le toucher.
• Respecter les consignes de montage, et notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit.
• Les panneaux latéraux du produit peuvent être chauds. Laisser le produit
refroidir avant de le toucher.
• Respecter les consignes de montage, et notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit.
RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE
• The product's side panels may be hot, allow the product to cool before
touching.
• Follow proper mounting instructions including torque values.
• Do not allow liquids or foreign objects to enter this product.
• The product's side panels may be hot, allow the product to cool before
touching.
• Follow proper mounting instructions including torque values.
• Do not allow liquids or foreign objects to enter this product.
Le non-respect de cette directive peut entraîner, des lésions corporelles
graves ou des dommages matériels.
graves ou des dommages matériels.
Failure to follow these instructions can result in
serious injury, or equipment damage.
serious injury, or equipment damage.
La mancata osservanza di questa precauzione può causare gravi rischi
per l'incolumità personale o danni alle apparecchiature.
per l'incolumità personale o danni alle apparecchiature.
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
producirse graves lesiones, daños materiales.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder
Materialschäden zur Folge haben.
Materialschäden zur Folge haben.
සփీኟඓኴႜኄၵ֡ፕຫLj
टᆶీሰׯჹዘට༹ฅ࡞ईኁยԢڦ࣋ă
टᆶీሰׯჹዘට༹ฅ࡞ईኁยԢڦ࣋ă
GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen,
bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein.
• Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen,
bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO
• I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare
il prodotto prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo apparecchio.
• I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare
il prodotto prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo apparecchio.
RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO
DE LA UNIDAD
• Los paneles laterales del producto pueden estar calientes. Esperar que
el producto se enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos extraños en el producto.
DE LA UNIDAD
• Los paneles laterales del producto pueden estar calientes. Esperar que
el producto se enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos extraños en el producto.
ଙ࣋ࢅߛ࿒ྔڦླ၃Ⴀ!
t!ׂڦᅃ֨௬ӱీඤLjሞഄૐඐമ൩փᄲةಸă
t!ፏቷኟඓڦҾጎຫLjԈઔ౦ਈኵă
t!൩ကඟᅂ༹तഄᅴԨׂă
t!ׂڦᅃ֨௬ӱీඤLjሞഄૐඐമ൩փᄲةಸă
t!ፏቷኟඓڦҾጎຫLjԈઔ౦ਈኵă
t!൩ကඟᅂ༹तഄᅴԨׂă
A
For 100 mA output SSRs, no airgap is required for full output current rating.
B
DRA-CN024Dxx
0.0
0.6
1.2
1.8
2.4
3.0
3.5
4.0
0
10
20
30
40
50
60
Ambient Temperature (°C)
Loa
d C
u
rr
e
nt
(A
m
p
e
re
s)
No air gap
Air gap ≥ 6.2 mm
DRA-CN048Dxx
0.00
0.02
0.04
0.06
0.08
0.10
0.12
0
10
20
30
40
50
60
Ambient Temperature (°C)
Loa
d C
u
rr
e
nt
(A
m
p
e
re
s)
B
No minimum
air gap required
air gap required
DRA-CN240Axx
0
10
20
30
40
50
60
0.0
0.3
0.7
1.0
1.3
1.7
2.0
2.3
Ambient Temperature (°C)
Loa
d C
u
rr
e
nt
(A
m
p
e
re
s)
No air gap
Air gap ≥ 6.2 mm
Rev: 021910