Texas Instruments MSP430F677xIPEU & MSP430F677x1IPEU 128-Pin target board MSP-TS430PEU128 MSP-TS430PEU128 Datenbogen
Produktcode
MSP-TS430PEU128
ECCN 5E002 TSPA - Technology / Software Publicly Available
MSP430F677x
,
MSP430F676x
,
MSP430F674x
SLAS768D – SEPTEMBER 2012 – REVISED DECEMBER 2013
Low-Power Mode With LCD Supply Currents (Into V
CC
) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
(1) (2)
Temperature (T
A
)
PARAMETER
V
CC
PMMCOREVx
-40°C
25°C
85°C
UNIT
TYP
MAX
TYP
MAX
TYP
MAX
0
2.5
3.1
9.1
I
LPM3
Low-power mode 3 (LPM3)
1
2.6
3.3
9.5
LCD,
current, LCD 4-mux mode,
3 V
µA
2
2.8
3.5
9.9
ext. bias
external biasing
(3) (4)
3
2.8
3.5
6.0
10.0
25.0
0
2.9
3.5
9.7
Low-power mode 3 (LPM3)
I
LPM3
1
3.1
3.7
10.1
current, LCD 4-mux mode,
LCD,
3 V
µA
internal biasing, charge
2
3.2
4.0
10.5
int. bias
pump disabled
(3) (5)
3
3.3
4.0
5.5
10.5
25.0
0
2.2
2.8
8.8
2.2 V
1
2.3
3.0
9.1
µA
Low-power mode 3 (LPM3)
2
2.5
3.2
9.5
I
LPM3
current, LCD 4-mux mode,
0
2.6
3.2
9.3
LCD,CP
internal biasing, charge
1
2.8
3.4
9.7
pump enabled
(3) (6)
3 V
µA
2
2.9
3.6
10.1
3
3.0
3.7
10.2
(1)
All inputs are tied to 0 V or to V
CC
. Outputs do not source or sink any current.
(2)
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external load
capacitance are chosen to closely match the required 12.5 pF.
capacitance are chosen to closely match the required 12.5 pF.
(3)
Current for watchdog timer and RTC clocked by ACLK included. ACLK = low frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3); f
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3); f
ACLK
= 32768 Hz, f
MCLK
= f
SMCLK
= f
DCO
= 0 MHz
Current for brownout, high side supervisor (SVS
H
) normal mode included. Low side supervisor and monitors disabled (SVS
L
, SVM
L
).
High side monitor disabled (SVM
H
). RAM retention enabled.
(4)
LCDMx = 11 (4-mux mode), LCDREXT = 1, LCDEXTBIAS = 1 (external biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 0 (charge pump
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (f
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (f
LCD
= 32768 Hz / 32 / 4 = 256 Hz)
Current through external resistors not included (voltage levels are supplied by test equipment).
Even segments S0,S2,... = 0, odd segments S1,S3,... = 1. No LCD panel load.
Even segments S0,S2,... = 0, odd segments S1,S3,... = 1. No LCD panel load.
(5)
LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 0 (charge pump
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (f
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (f
LCD
= 32768 Hz / 32 / 4 = 256 Hz)
Even segments S0,S2,... = 0, odd segments S1,S3,... = 1. No LCD panel load.
(6)
LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 1 (charge pump
enabled), VLCDx = 1000 (V
enabled), VLCDx = 1000 (V
LCD
= 3V,typ.), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (f
LCD
= 32768 Hz / 32 / 4 = 256 Hz)
Even segments S0,S2,... = 0, odd segments S1,S3,... = 1. No LCD panel load.
62
Copyright © 2012–2013, Texas Instruments Incorporated