Texas Instruments CC2650DK Benutzerhandbuch
General-Purpose Timer Registers
13.5.1.7 RIS Register (Offset = 1Ch) [reset = X]
RIS is shown in
and described in
.
Raw Interrupt Status Associated registers: IMR, MIS, ICLR
Figure 13-15. RIS Register
31
30
29
28
27
26
25
24
RESERVED
R-X
23
22
21
20
19
18
17
16
RESERVED
WURIS
R-X
R-X
15
14
13
12
11
10
9
8
RESERVED
DMABRIS
RESERVED
TBMRIS
CBERIS
CBMRIS
TBTORIS
R-X
R-X
R-X
R-X
R-X
R-X
R-X
7
6
5
4
3
2
1
0
RESERVED
DMAARIS
TAMRIS
RTCRIS
CAERIS
CAMRIS
TATORIS
R-X
R-X
R-X
R-X
R-X
R-X
R-X
Table 13-14. RIS Register Field Descriptions
Bit
Field
Type
Reset
Description
31-17
RESERVED
R
X
Software should not rely on the value of a reserved. Writing any
other value than the reset value may result in undefined behavior.
other value than the reset value may result in undefined behavior.
16
WURIS
R
X
GPT Write Update Error Raw Interrupt 0: No error. 1: Either Timer A
or B was written twice in a Row or Timer A was written before the
corresponding Timer B was written.
or B was written twice in a Row or Timer A was written before the
corresponding Timer B was written.
15-14
RESERVED
R
X
Software should not rely on the value of a reserved. Writing any
other value than the reset value may result in undefined behavior.
other value than the reset value may result in undefined behavior.
13
DMABRIS
R
X
GPT Timer B DMA Done Raw Interrupt Status 0: Transfer has not
completed 1: Transfer has completed
completed 1: Transfer has completed
12
RESERVED
R
X
Software should not rely on the value of a reserved. Writing any
other value than the reset value may result in undefined behavior.
other value than the reset value may result in undefined behavior.
11
TBMRIS
R
X
GPT Timer B Match Raw Interrupt 0: The match value has not been
reached 1: The match value is reached. TBMR.TBMIE is set, and
the match values in TBMATCHR and optionally TBPMR have been
reached when configured in one-shot or periodic mode.
reached 1: The match value is reached. TBMR.TBMIE is set, and
the match values in TBMATCHR and optionally TBPMR have been
reached when configured in one-shot or periodic mode.
10
CBERIS
R
X
GPT Timer B Capture Mode Event Raw Interrupt 0: The event has
not occured. 1: The event has occured. This interrupt asserts when
the subtimer is configured in Input Edge-Time mode
not occured. 1: The event has occured. This interrupt asserts when
the subtimer is configured in Input Edge-Time mode
9
CBMRIS
R
X
GPT Timer B Capture Mode Match Raw Interrupt 0: Match for Timer
B has not occured 1: Match for Timer B has occurred. This interrupt
asserts when the values in the TBR and TBPR match values in the
TBMATCHR and TBPMR, and when configured in Input Edge-Time
mode (reg-ref instead!!)
B has not occured 1: Match for Timer B has occurred. This interrupt
asserts when the values in the TBR and TBPR match values in the
TBMATCHR and TBPMR, and when configured in Input Edge-Time
mode (reg-ref instead!!)
8
TBTORIS
R
X
GPT Timer B Time-out Raw Interrupt 0: Timer B has not timed out 1:
Timer B has timed out. This interrupt is asserted when a one-shot or
periodic mode timer reaches it's count limit. The count limit is 0 or
the value loaded into TBILR, depending on the count direction.
Timer B has timed out. This interrupt is asserted when a one-shot or
periodic mode timer reaches it's count limit. The count limit is 0 or
the value loaded into TBILR, depending on the count direction.
7-6
RESERVED
R
X
Software should not rely on the value of a reserved. Writing any
other value than the reset value may result in undefined behavior.
other value than the reset value may result in undefined behavior.
5
DMAARIS
R
X
GPT Timer A DMA Done Raw Interrupt Status 0: Transfer has not
completed 1: Transfer has completed
completed 1: Transfer has completed
4
TAMRIS
R
X
**GPT **Timer A Match Raw Interrupt 0: The match value has not
been reached 1: The match value is reached. TAMR.TAMIE is set,
and the match values in TAMATCHR and optionally TAPMR have
been reached when configured in one-shot or periodic mode.
been reached 1: The match value is reached. TAMR.TAMIE is set,
and the match values in TAMATCHR and optionally TAPMR have
been reached when configured in one-shot or periodic mode.
1098
Timers
SWCU117A – February 2015 – Revised March 2015
Copyright © 2015, Texas Instruments Incorporated