Panasonic Limit switch 125 Vac 0.1 A Tappet momentary AZH2332CEJ IP67 1 pc(s) AZH2332CEJ Datenbogen
Produktcode
AZH2332CEJ
26
MOUNTING METHOD
Die cast case
1. Side mounting (all types)
M4 screw is used for mounting on side.
Mount it firmly with washer. Mounting
torque is 1.37 to 1.57 N.m.
Remove the hexagonal nut when plunger
type is used in side mounting.
1. Side mounting (all types)
M4 screw is used for mounting on side.
Mount it firmly with washer. Mounting
torque is 1.37 to 1.57 N.m.
Remove the hexagonal nut when plunger
type is used in side mounting.
2. Panel mounting (Panel plunger type)
When the panel mounting type is fixed
on the panel, the torque of hexagonal nut
is set under 7.84 N.m.
When the panel mounting type is fixed
on the panel, the torque of hexagonal nut
is set under 7.84 N.m.
Plastic case
Side mounting (all types)
M4 screw is used for mounting on side.
Mount it firmly with washer. Mounting
torque is 1.18 to 1.47 N.m.
Side mounting (all types)
M4 screw is used for mounting on side.
Mount it firmly with washer. Mounting
torque is 1.18 to 1.47 N.m.
APPLICABLE WIRE
(For screw terminal)
Sealed rubber of the lead wire is applica-
ble for 6 dia. to 8 dia.
ble for 6 dia. to 8 dia.
Applicable wire
Electric
wire name
Wire
strand
2-wire
6.6 mm dia.
7.4 mm dia.
8.0 mm dia.
7.4 mm dia.
8.0 mm dia.
7.0 mm dia.
7.8 mm dia.
7.8 mm dia.
0.75 mm
2
1.25 mm
2
2.0 mm
2
0.75 mm
2
1.25 mm
2
3-wire
Conductor
Finished
outside
diameter
Vinyl cab-
tyre cord
(VCTF)
WIRING
(For screw terminal)
M3 small binding screw is used as a ter-
minal screw. When wiring, don’t connect
the lead wire to the terminal directly.
Fasten the crimped terminals securely
applying a tightening torque of 0.20 to
0.29 N.m.
minal screw. When wiring, don’t connect
the lead wire to the terminal directly.
Fasten the crimped terminals securely
applying a tightening torque of 0.20 to
0.29 N.m.
Take note the terminal arrangement is
different between plunger type and lever
type. The arrangement of N.C. and N.O.
is reversed.
different between plunger type and lever
type. The arrangement of N.C. and N.O.
is reversed.
CONNECTOR TYPE
1) The cord outlet direction is inter-
changeable. Refer to “How to change the
cord outlet direction”.
2) Do not remove the connector over 50
times.
3) Wiring diagram as shown below.
changeable. Refer to “How to change the
cord outlet direction”.
2) Do not remove the connector over 50
times.
3) Wiring diagram as shown below.
4) When the angle type of connector
cord is used, the cord outlet direction is
as follows.
cord is used, the cord outlet direction is
as follows.
Cord outlet direction (Right side)
Cord outlet direction (Left side)
Note: Contact No. 1 is not in use.
14.5
±0.2 dia.
.571
±.008 dia.
Panel mounting hole dimensions
2-4.3 dia. or M4 screw hole
2-.169 dia.
33
±0.15
1.299
±.006
Side mounting hole dimensions
2-4.3 dia. or M4 screw hole
2-.169 dia.
33
±0.15
1.299
±.006
Side mounting hole dimensions
N.C.
terminal
terminal
N.O.
terminal
terminal
COM
terminal
terminal
Plunger type
N.O.
terminal
terminal
N.C.
terminal
terminal
COM
terminal
terminal
Lever type
Approx. 30
Approx. 45
Approx. 1.772
Approx. 15
Approx. .591
Approx. 1.181
N.C.
Contact No. 2
N.O.
Contact No. 4
COM
Contact No. 3
Contact No. of connector
2
1
4
3
HL (AZH)
04/2005