MULTIPLEX RX-7-DR light 55810 Datenbogen
Produktcode
55810
Operating Instructions RX-6-DR light M-LINK /
RX-7-DR light M-LINK 2.4 GHz receiver
Page 7
Instru
ctions: RX-6/7-DR l
ight M-L
INK
2.4
GHz re
ceiver #
82 5490
(09-
07-16
/MIWA)
•
Er
ror
s an
d omission
s excep
ted!
•
©
M
U
LT
IPL
E
X
!
These operating instructions are an integral part
of the product, and contain important information
and safety notes. Please store them in a safe place,
where you can find them at any time, and pass
them on to the new owner if you sell the receiver.
1. S
PECIFICATION
RX-6-DR light
M-LINK
RX-7-DR light
M-LINK
Order No.
# 5 5809
# 5 5810
Reception system
2.4 GHz FHSS M-LINK
Frequency Hopping Spread Spectrum
MULTIPLEX-LINK
Servo channel count
6 7
Servo signal frame
rate
rate
Fast response: 14 ms
Standard: 21 ms
Signal resolution
12-bit, 3872 steps
Current drain
Approx. 10 mA (excl. servos)
Aerial feed length /
aerial length
aerial length
Feed cable: approx. 10 cm (2 x)
Aerial: approx. 3 cm (2 x)
Operating voltage
3.5 V … 9.0 V
Î
4 - 6 NiCd / NiMH cells (NiXX)
Î
2S LiPo / LiIo
Operating
temperature range
temperature range
- 20
°C … + 55
°C
Weight
10 g
Dimensions
Approx. 38.0 x 28.0 x 11.5 mm
2. S
PECIAL
F
EATURES
• Small, all-purpose 6-channel / 7-channel receiver exploiting
MULTIPLEX 2.4 GHz M-LINK technology, ideal for use in
small models.
small models.
• Dual
receiver:
The receiver contains two complete receiving circuits which
operate in parallel (receiver diversity).
This provides excellent reception quality by minimising
directional effects.
operate in parallel (receiver diversity).
This provides excellent reception quality by minimising
directional effects.
• In-line connector arrangement:
Ideal for use even in slender fuselages (e.g. F3B, F3J, …).
• HOLD / FAIL-SAFE function.
• Integral SET button and LED:
• Integral SET button and LED:
For binding, FAIL-SAFE programming, RESET and
operating status information.
operating status information.
3. S
AFETY
N
OTES
! Please read the instructions before using the receiver.
! Use the receiver only for the intended applications
! Use the receiver only for the intended applications
(Î 4.).
! Ensure the power supply is of adequate capacity (Î 6.).
! Observe the installation notes (Î 9.).
! Carry out regular range checks (Î 10.).
! Observe the installation notes (Î 9.).
! Carry out regular range checks (Î 10.).
4. A
PPLICATION
The
RX-6/7-DR light M-LINK is a radio control receiver inten-
ded exclusively for use in model sport applications. It is prohi-
bited to use it for other applications, such as man-carrying
vehicles or industrial installations.
bited to use it for other applications, such as man-carrying
vehicles or industrial installations.
The RX-6/7-DR light M-LINK was designed with minimum
possible size and weight as top priority, and for technical rea-
sons such a unit cannot offer the same reception characteristics
as a larger, technically more sophisticated and more expensive
receiver. In the interests of safety we recommend that you use a
larger receiver wherever space permits. However, under normal
conditions it is possible to obtain an excellent reception perfor-
mance with the RX-6/7-DR light M-LINK provided that all the
RC components are arranged carefully, and the two receiver
aerials are deployed correctly.
possible size and weight as top priority, and for technical rea-
sons such a unit cannot offer the same reception characteristics
as a larger, technically more sophisticated and more expensive
receiver. In the interests of safety we recommend that you use a
larger receiver wherever space permits. However, under normal
conditions it is possible to obtain an excellent reception perfor-
mance with the RX-6/7-DR light M-LINK provided that all the
RC components are arranged carefully, and the two receiver
aerials are deployed correctly.
5. C
OMPATIBILITY
The RX-6/7-DR light M-LINK 2.4 GHz receiver can only be used
in conjunction with transmitters which use MULTIPLEX M-LINK
transmission technology. As of June 2009 these are:
• ROYALpro 7, 9 and 16 M-LINK.
• ROYALevo or pro 7, 9 and 12 with firmware version V3.xx
in conjunction with transmitters which use MULTIPLEX M-LINK
transmission technology. As of June 2009 these are:
• ROYALpro 7, 9 and 16 M-LINK.
• ROYALevo or pro 7, 9 and 12 with firmware version V3.xx
and the HFM4 M-LINK 2.4 GHz RF module.
• PROFImc 3010, 3030 and 4000 with the HFM3 M-LINK
2.4 GHz RF module.
• COCKPIT SX M-LINK.
• MULTIPLEX transmitters with the HFMx M-LINK 2.4 GHz
• MULTIPLEX transmitters with the HFMx M-LINK 2.4 GHz
RF module.
6. P
OWER
S
UPPLY
The RX-6/7-DR light M-LINK receiver works with a wide range
of voltages from 3.5 V … 9.0 V, i.e. with receiver batteries con-
sisting of 4 to 6 NiXX cells or 2S LiPo / 2S LiIo batteries.
! Note: if you wish to use a five-cell (six-cell) NiXX battery,
check that all the servos, gyros and other components to be
connected to the system are approved by the manufacturer for
use on operating voltages up to 7.5 V (9.0 V). If you wish to use
a 2S LiPo (2S LiIo) pack, check that all the servos, gyros and
other components to be connected to the system are approved
by the manufacturer for use on up to 8.4 V (8.2 V).
! Note: ensure that the power supply is adequate
A power supply system in good condition and of adequate
capacity for the specific application plays an indispensable role
in the safe operation of any model:
• Use only high-quality receiver batteries of adequate capacity.
of voltages from 3.5 V … 9.0 V, i.e. with receiver batteries con-
sisting of 4 to 6 NiXX cells or 2S LiPo / 2S LiIo batteries.
! Note: if you wish to use a five-cell (six-cell) NiXX battery,
check that all the servos, gyros and other components to be
connected to the system are approved by the manufacturer for
use on operating voltages up to 7.5 V (9.0 V). If you wish to use
a 2S LiPo (2S LiIo) pack, check that all the servos, gyros and
other components to be connected to the system are approved
by the manufacturer for use on up to 8.4 V (8.2 V).
! Note: ensure that the power supply is adequate
A power supply system in good condition and of adequate
capacity for the specific application plays an indispensable role
in the safe operation of any model:
• Use only high-quality receiver batteries of adequate capacity.
Balance and maintain them carefully, and charge them fully.
• Ensure that all cables are of adequate conductor cross-
section. Keep all wiring as short as possible, and use the
absolute minimum of plug / socket connections.
absolute minimum of plug / socket connections.
• Use high-quality switch harnesses exclusively.
• Brief collapses in the power supply voltage (lasting a few
• Brief collapses in the power supply voltage (lasting a few
milli-seconds) have no adverse effect on the receiver. Longer
voltage collapses to below 3.5 V may cause a receiver reset,
resulting in a brief interruption in reception. This may be due
to a receiver battery which is almost flat, too weak or defec-
tive, cables of inadequate cross-section, poor-quality con-
nectors or an overloaded or defective BEC system.
voltage collapses to below 3.5 V may cause a receiver reset,
resulting in a brief interruption in reception. This may be due
to a receiver battery which is almost flat, too weak or defec-
tive, cables of inadequate cross-section, poor-quality con-
nectors or an overloaded or defective BEC system.