Samsung Car Satellite TV System 8000 Benutzerhandbuch
33
English
04
Advanced Featur
es
Network Setup (Samsung Auto
Configuration)
Configuration)
The Samsung Auto Configuration function lets you connect
your Samsung TV automatically to non-Samsung wireless
APs. If your non-Samsung AP does not support Samsung
Auto Configuration, you must connect using one of the
other methods: PBC (WPS), auto configuration, or manual
configuration.
your Samsung TV automatically to non-Samsung wireless
APs. If your non-Samsung AP does not support Samsung
Auto Configuration, you must connect using one of the
other methods: PBC (WPS), auto configuration, or manual
configuration.
✎
To use this function, you must set SWL (Samsung
Wireless Link) to Off in the TV’s on-screen menu.
Wireless Link) to Off in the TV’s on-screen menu.
✎
You can check for equipment that supports Samsung
Auto Configuration on www.samsung.com.
Auto Configuration on www.samsung.com.
How to set up using Samsung Auto Configuration
1. Place the AP and TV next to each other and turn them
on.
✎
Because AP booting times vary, you may have
to wait approximately two minutes for your AP to
boot up.
to wait approximately two minutes for your AP to
boot up.
✎
Ensure the LAN cable is connected to the
WAN port of the AP during Samsung Auto
Configuration. If it is not connected, Samsung
Auto Configuration only confirms that the TV is
connected to the AP, but does not confirm it is
connected to the Internet.
WAN port of the AP during Samsung Auto
Configuration. If it is not connected, Samsung
Auto Configuration only confirms that the TV is
connected to the AP, but does not confirm it is
connected to the Internet.
2. After 2 minutes, connect the Samsung Wireless LAN
Adapter to the TV. When the Samsung Wireless LAN
Adapter establishes a connection with your TV, a pop-up
window appears.
Adapter establishes a connection with your TV, a pop-up
window appears.
3. As soon as a connection is established, place the AP
parallel to the Samsung Wireless LAN Adapter and not
farther than 9 and 7/8s inches (25cm) from it.
farther than 9 and 7/8s inches (25cm) from it.
4. Wait until the connection is automatically established.
✎
If Samsung Auto Configuration does not connect
your TV to your AP, a pop-up window appears on
the screen notifying you of the failure. If you want
to try using Samsung Auto Configuration again,
reset the AP, disconnect the Samsung Wireless
LAN Adapter and then try again from Step 1. You
can also choose one of the other connection
setup methods: PBC (WPS), auto, or manual.
your TV to your AP, a pop-up window appears on
the screen notifying you of the failure. If you want
to try using Samsung Auto Configuration again,
reset the AP, disconnect the Samsung Wireless
LAN Adapter and then try again from Step 1. You
can also choose one of the other connection
setup methods: PBC (WPS), auto, or manual.
5. Place the AP in a desired location.
✎
If the AP settings change or you install a new
AP, you must perform the Samsung Auto
Configuration procedure again, beginning from
Step 1.
AP, you must perform the Samsung Auto
Configuration procedure again, beginning from
Step 1.
Notice
The picture may appear corrupted or have static for some channels when the TV is connected to the Samsung Wireless LAN
Adapter. In such a case, establish a connection using one of the following methods or connect the Samsung Wireless LAN
Adapter using a USB cable in a place that is not affected by radio interference.
Adapter. In such a case, establish a connection using one of the following methods or connect the Samsung Wireless LAN
Adapter using a USB cable in a place that is not affected by radio interference.
Method 1
Method 2
Connect using the USB right angle adapter
Connect via an extension cable
To connect the Samsung Wireless LAN Adapter using the USB
right angle adapter, follow these steps:
right angle adapter, follow these steps:
1. Connect the USB right angle adapter to the Samsung
Wireless LAN Adapter.
2. Connect the other end of the right angle adapter to the
USB
1 (HDD)
port.
To reconnect the Samsung Wireless LAN Adapter using
the extension cable, follow these steps:
the extension cable, follow these steps:
✎
The Samsung Wireless LAN Adapter should be
installed in an interference-free area in order to
avoid interference between the adapter and tuner.
installed in an interference-free area in order to
avoid interference between the adapter and tuner.
1. Connect the extension cable to the
USB 1 (HDD)
port.
2. Connect the extension cable and Samsung Wireless
LAN Adapter.
3. Attach the Samsung Wireless LAN Adapter to the
back of the TV near the top, using double-sided
adhesive tape.
adhesive tape.
or
|j_WWWTuhiu]_TWY^XYhTW]sWZUGGGZZ
YWXWTW`TWXGGG㝘㤸GXWa[^aXY