Leupold Oven PS536GS Benutzerhandbuch
17
E
N
G
L
IS
H
SECTION 3 - OPERATION
CAUTION
In case of power failure, turn all switches to the “OFF” ("O")
position, open the oven window, and remove the product.
After the power has been restored, perform the normal
startup procedure. IF THE OVEN WAS SWITCHED OFF
FOR LESS THAN 5 MINUTES, WAIT FOR AT LEAST FIVE
MINUTES BEFORE RESTARTING THE OVEN.
position, open the oven window, and remove the product.
After the power has been restored, perform the normal
startup procedure. IF THE OVEN WAS SWITCHED OFF
FOR LESS THAN 5 MINUTES, WAIT FOR AT LEAST FIVE
MINUTES BEFORE RESTARTING THE OVEN.
The burner will not operate and gas will not flow through
the burner without electric power. No attempt should be
made to operate the oven during a power failure.
the burner without electric power. No attempt should be
made to operate the oven during a power failure.
IMPORTANT
On gas ovens, if the "HEAT ON" light will not illuminate, OR
if the oven does not heat, the gas burner may not have lit.
Turn the "HEAT" (
if the oven does not heat, the gas burner may not have lit.
Turn the "HEAT" (
), "BLOWER"
(
)
, and "CONVEYOR"
(
) switches to the "OFF" ("O") position. Wait for AT
LEAST FIVE MINUTES before restarting the oven. Then,
repeat the Daily Startup procedure.
repeat the Daily Startup procedure.
A.
DAILY STARTUP PROCEDURE
3.
Turn the "CONVEYOR"
(
(
) switch to the “ON”
("I") position.
4.
If necessary, adjust the
conveyor speed setting
by pressing the
conveyor speed setting
by pressing the
or
pushbuttons on the con-
veyor speed controller to
change the displayed
bake time.
veyor speed controller to
change the displayed
bake time.
6.
Turn the "HEAT" (
)
switch to the "ON" ("I")
position, and wait for the
"HEAT ON" light to turn
on.
position, and wait for the
"HEAT ON" light to turn
on.
8.
(Optional) Press the Tem-
perature ( ) key to show
the Actual Temperature
in the display, and wait
for the "ACTUAL TEMP"
light to turn on. This al-
lows you to monitor the
oven temperature as it
rises to the setpoint.
the Actual Temperature
in the display, and wait
for the "ACTUAL TEMP"
light to turn on. This al-
lows you to monitor the
oven temperature as it
rises to the setpoint.
1.
Turn the "HEAT" (
) and
"BLOWER" (
) swit-
ches to the "OFF" ("O")
position. Note that the
blowers will remain in op-
eration until the oven has
cooled to below 200°F
(93°C).
position. Note that the
blowers will remain in op-
eration until the oven has
cooled to below 200°F
(93°C).
II. NORMAL OPERATION - STEP-BY-STEP
7.
Wait for the oven to heat to the setpoint temperature. Higher
setpoint temperatures will require a longer wait. The oven
can reach a temperature of 500°F (232°C) in approximately
5 minutes.
setpoint temperatures will require a longer wait. The oven
can reach a temperature of 500°F (232°C) in approximately
5 minutes.
3.
Open the window to allow the oven to cool faster.
2.
Make certain that there
are no products left on
the conveyor inside the
oven. Turn the "CON-
VEYOR" (
are no products left on
the conveyor inside the
oven. Turn the "CON-
VEYOR" (
) switch to
the "OFF" ("O") position.
2.
Turn the "BLOWER"
(
)
switch to the “ON” ("I")
position.
position.
•
Press the Up Arrow
and Down Arrow
Keys as necessary
to adjust the set-
point.
and Down Arrow
Keys as necessary
to adjust the set-
point.
5.
Adjust the temperature
controller to a desired set
temperature, if neces-
sary.
controller to a desired set
temperature, if neces-
sary.
•
Press the Set Point
and Unlock keys at
the same time. Wait
for the "SET PT" light
to turn on.
and Unlock keys at
the same time. Wait
for the "SET PT" light
to turn on.
B.
DAILY SHUTDOWN PROCEDURE
9.
Allow the oven to preheat for 10 minutes after it has reached
the set point temperature.
the set point temperature.
+
4.
After the oven has cooled and the blowers have turned off,
switch the circuit breaker/fused disconnect to the off posi-
tion.
switch the circuit breaker/fused disconnect to the off posi-
tion.
1.
Check that the circuit breaker/fused disconnect is in the on
position. Check that the window is closed.
position. Check that the window is closed.
+
wait
for
or
wait
for
or
wait
for