FieldServer Technologies Video Game Controller 1.1 Benutzerhandbuch
Ruinet Utility User Manual
Page 11 of 46
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com
2.3.1.
Connection Overview – Settings Aspect.
Parameter
Description
Connection
The current connection out of the total number of connections.
Adapter
An adapter ID is displayed if the driver is an adapter driver.
Poll_Delay
The minimum amount of time that must pass between one Client Map
Descriptor completing its task and the next Client Map Descriptor being
serviced. Refer to Driver Manuals.
Descriptor completing its task and the next Client Map Descriptor being
serviced. Refer to Driver Manuals.
Low_Pri_Poll_Delay
The poll delay used for lower priority Map Descriptors.
Server_Hold_Timeout
When an upstream device polls the FieldServer, and the data is
unavailable or too old, the driver generates a poll to the downstream
device for fresh data, (port expansion). The Server_Hold_Timeout
defines the time available for this transaction to complete before an error
is returned. The default is 2 seconds.
unavailable or too old, the driver generates a poll to the downstream
device for fresh data, (port expansion). The Server_Hold_Timeout
defines the time available for this transaction to complete before an error
is returned. The default is 2 seconds.
Protocol
The name of the protocol used by this connection.
IP_Address
An IP address for the connection if applicable.
Remote_IP_Address
A remote IP address for the connection if applicable.
Port
Identifies the port for a serial driver. P1... P8 or R1...R2
Timeout*
The timeout defined for the connection. Default 2 seconds. See Error!
Reference source not found. for further information.
Reference source not found. for further information.
Recovery_Interval
The time after a node goes off-line before the driver tries to poll the
device again. Default 30 seconds.
device again. Default 30 seconds.
Probation_Delay
The length of time communication needs to be re-established for before
an offline Client node is marked on-line again. Default 1 minute.
an offline Client node is marked on-line again. Default 1 minute.
Connection_Mode
Server (passive) or client (active).
Client/Server_Mode
Optional setting to force a connection mode. Possible values are Server,
PLC, Hot_Standby, Hot_Standby_Data, Client_Only, Diagnostic.
PLC, Hot_Standby, Hot_Standby_Data, Client_Only, Diagnostic.
Multidrop_Mode
Indicates whether Multidrop mode is enabled or not. Refer to Error!
Reference source not found. for more information.
Reference source not found. for more information.
Turnaround_Delay
The delay that the driver imposes between receiving a poll and sending a
response. The default is 5ms for serial drivers.
response. The default is 5ms for serial drivers.
Baud
Connection baud rate used by serial drivers. Some drivers override this
value because the communication protocol allows the baud rate to be
changed by the master.
value because the communication protocol allows the baud rate to be
changed by the master.
Data_bits
The number of data bits used for serial communication by the
connection. The values are 7 or 8.
connection. The values are 7 or 8.
Parity
The parity mode used by the connection to detect communication errors.
Values are even, odd or none. The default is none.
Values are even, odd or none. The default is none.
Stop_Bits
The number of stop bits used for serial communication by the
connection. The values are 1 or 2.
connection. The values are 1 or 2.
Line_drive_on
Time a serial driver using RS-485 will wait before driving the
communications line after receiving permission. Default is 1milisecond.
communications line after receiving permission. Default is 1milisecond.
Line_drive_off
Time that a communication line using RS-485 is actively driven before
being released, after the last bit has been sent. Default 1milisecond..
being released, after the last bit has been sent. Default 1milisecond..
IC_timeout
Time a driver will wait between receiving the first and second bytes of a
message before generating an IC Timeout. Default 0.5 seconds. See
Error! Reference source not found. for more information.
message before generating an IC Timeout. Default 0.5 seconds. See
Error! Reference source not found. for more information.
IP_port
Remote_IP_Port
Max_Master
Max_Info_Frames
Connection_Type
Remote_IP_Port
Max_Master
Max_Info_Frames
Connection_Type
Determined by specific driver or protocol used. See Driver Manual.