West Elm Staggered Chandelier Large Montageanweisungen
Important Safety Instructions:
These instructions are provided for your safety. It is important that they are read carefully and completely
before installing the chandelier.
We strongly recommend that a professional electrician install all direct wire fi xtures.
This fi xture has been rated for up to 8x60-watt TYPE B bulbs (not included). To avoid the risk of fi re, do not
exceed the recommended wattage.
These instructions are provided for your safety. It is important that they are read carefully and completely
before installing the chandelier.
We strongly recommend that a professional electrician install all direct wire fi xtures.
This fi xture has been rated for up to 8x60-watt TYPE B bulbs (not included). To avoid the risk of fi re, do not
exceed the recommended wattage.
Pre-assembly:
Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any
contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
For your safety and convenience, assembly by two people is recommended.
Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any
contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
For your safety and convenience, assembly by two people is recommended.
WARNING: This lighting fi xture contains lead, a chemical known to the State of California to cause cancer,
birth defects and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise
touching this light fi xture
birth defects and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise
touching this light fi xture
Parts Enclosed:
(1) Mounting plate (D)
(1) Canopy (E)
(1) Metal Plate (G)
(1) Pole (J)
(1) Pole (K)
(8) Lamp Shade (L)
(8) Socket (M)
(1) Ground Ring (P)
(1) Pole (T)
(8) Socket Ring (U)
(1) Mounting plate (D)
(1) Canopy (E)
(1) Metal Plate (G)
(1) Pole (J)
(1) Pole (K)
(8) Lamp Shade (L)
(8) Socket (M)
(1) Ground Ring (P)
(1) Pole (T)
(8) Socket Ring (U)
To Assemble:
1.SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
2.Carefully unpack all fi xture parts and hardware and lay out on a clear workspace.
3.Unscrew the Socket Ring (U) from the Socket (M)
4.Place the Lamp Shade(L) onto the Socket(M) and screw the Socket Ring (U) back onto the Socket (M),
tighten by hand Repeat for all 8 sockets.
5.Screw the Pole (K) onto the Pole (T)
6.Screw the Pole (J) onto the Pole (K)
7.Consumer can adjust the light height by Attached Pole(J). To shorten light remove Pole (J).
8.Align the Metal Plate(G) hole with the Pole(J) and take the Metal Plate (G) onto the Pole (J)
1.SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
2.Carefully unpack all fi xture parts and hardware and lay out on a clear workspace.
3.Unscrew the Socket Ring (U) from the Socket (M)
4.Place the Lamp Shade(L) onto the Socket(M) and screw the Socket Ring (U) back onto the Socket (M),
tighten by hand Repeat for all 8 sockets.
5.Screw the Pole (K) onto the Pole (T)
6.Screw the Pole (J) onto the Pole (K)
7.Consumer can adjust the light height by Attached Pole(J). To shorten light remove Pole (J).
8.Align the Metal Plate(G) hole with the Pole(J) and take the Metal Plate (G) onto the Pole (J)
Hardware Included:
•(3) Plastic wire connectors (A)
•(1) Green ground screws (B)
•(2) Mounting screws (C)
•(4) Canopy screws (F)
•(7) Pole (J)
•(1) Pole (K)
•(1) Iron Wrench ( R)
•(1) Iron Key (S)
•(3) Plastic wire connectors (A)
•(1) Green ground screws (B)
•(2) Mounting screws (C)
•(4) Canopy screws (F)
•(7) Pole (J)
•(1) Pole (K)
•(1) Iron Wrench ( R)
•(1) Iron Key (S)
To install you will need:
•Electrical tape
•Screwdriver
•2 people recommended
•Electrical tape
•Screwdriver
•2 people recommended