West Elm Furniture Tipping Restraint Montageanweisungen
FURNITURE TIPPING RESTRAINT
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Manufacturer assumes no liability for improper installation or
excessive loads placed on screws, brackets or straps.
excessive loads placed on screws, brackets or straps.
Young children may be injured by tipping furniture and the use of a tipping restraint is highly recommended.
When properly installed, this restraint will provide protection against tipping of furniture. This tipping restraint MUST be secured to a wall-stud or wall structure
of similar strength.
of similar strength.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Hardware included:
(2) Brackets
(2) Brackets
(1) Nylon Strap
(2) Long (1-1/4”) Stud Mounting Screws
(2) Short (3/4”) Furniture-Side Mounting Screws
Note: For safe mounting it is essential to use the proper hardware for your wall type. The included hardware is for drywall or stud mounting only. For other
wall types (e.g., plaster, concrete and brick) please consult your local hardware store for fastener advice.
wall types (e.g., plaster, concrete and brick) please consult your local hardware store for fastener advice.
To install:
1) LOCATING THE STUDS: Use a stud finder to locate the vertical wooden studs within your wall located behind the final
position of the furniture item. Mark the stud locations with a light pencil-mark.
position of the furniture item. Mark the stud locations with a light pencil-mark.
2) MOUNTING THE FURNITURE-SIDE BRACKET: Move the furniture item close to the wall to its final position. Use
pieces of tape or a pencil to transcribe the stud locations of the wall onto the furniture item. Move the furniture item again so
you can access its back and use the marks to locate a suitable mounting point for the furniture-side bracket. Make sure that
the bracket is secured to a firm portion of the furniture frame and as high as possible. Remember: The furniture-side bracket
must be positioned near a wall stud. Using a pencil, and the bracket as a guide, mark “screw marks” on the furniture item
through the bracket holes.
pieces of tape or a pencil to transcribe the stud locations of the wall onto the furniture item. Move the furniture item again so
you can access its back and use the marks to locate a suitable mounting point for the furniture-side bracket. Make sure that
the bracket is secured to a firm portion of the furniture frame and as high as possible. Remember: The furniture-side bracket
must be positioned near a wall stud. Using a pencil, and the bracket as a guide, mark “screw marks” on the furniture item
through the bracket holes.
Use a 3/32” drill bit to drill pilot holes into the furniture item at the “screw marks”. Use the TWO Short screws to secure the
furniture-side bracket. This bracket can be positioned either vertically or horizontal as necessary (See Figure 1).
furniture-side bracket. This bracket can be positioned either vertically or horizontal as necessary (See Figure 1).
3) MOUNTING THE WALL-SIDE BRACKET: Position the wall-side bracket along the selected stud mark so that it will be
adjacent the furniture-side bracket when the furniture item is moved to its final position. The wall-side bracket should be about
ONE inch lower than the furniture-side bracket (See Figure 3). Use the TWO Long screws to secure the wall-side bracket to
the wall. Remember to position the wall-side bracket vertically so that both screws will engage the selected wall stud (See
Figure 2).
adjacent the furniture-side bracket when the furniture item is moved to its final position. The wall-side bracket should be about
ONE inch lower than the furniture-side bracket (See Figure 3). Use the TWO Long screws to secure the wall-side bracket to
the wall. Remember to position the wall-side bracket vertically so that both screws will engage the selected wall stud (See
Figure 2).
4) ATTACHING THE STRAP: When both brackets are securely attached, move the furniture to its final desired position and
thread the strap through the openings of each bracket and also through the ratcheting “buckle”. Tighten the strap until several
“clicks” are heard. The furniture item is now securely tethered to the wall.
thread the strap through the openings of each bracket and also through the ratcheting “buckle”. Tighten the strap until several
“clicks” are heard. The furniture item is now securely tethered to the wall.
Note: If you must move the furniture item, you can release the strap by depressing the lever arm located at its buckle and simultaneously withdrawing the
strap from the buckle. Make sure to reconnect the strap once the furniture item is returned to its previous position.
strap from the buckle. Make sure to reconnect the strap once the furniture item is returned to its previous position.
Figure 1
Figure 2
Figure 3
Rev. date
25-Apr-12
25-Apr-12