Panasonic Attune II Installationsanleitung

9



wOperating precautions



p This unit is for indoor use only. 

It cannot be used outdoors. 
Avoid installation in a location where the unit will be 
exposed to direct sunlight for extended periods or near a 
cooling or heating appliance. 
Otherwise, deformation, discoloration, malfunctioning 
and/or problems in operation may result. Operate the unit 
where it will not be splashed or sprayed by water.



p Handle the unit carefully. This product uses parts that 

may be damaged by improper handling or storage.



p Do not use this unit in an atmosphere where there are 

flammable gases. Otherwise, an explosion may occur, 
resulting in injuries.



p Do not install this unit in a location that is susceptible 

to salt damage or where corrosive gases are given off. 
Otherwise, the mounting parts will deteriorate, and this 
unit may fall, resulting in injury or accidents.



p Tighten the screws and bolts using the designated 

torque. Otherwise, this unit may fall, resulting in injury or 
accidents.



p Install this unit on a surface that can bear its weight. 

Otherwise, this unit may fall or topple over, resulting in 
injury or accidents. Installation work should be started 
only after sufficient reinforcement is completed.



p Insert the AC plug completely. If the plug is not inserted 

completely, fire due to overheating or electric shock may 
result. Do not use a damaged plug or loose AC outlet.



p Do not pull or insert the AC plug if your hands are wet. 

Electric shock may result.



p Do not place containers with water or other liquids on top 

of or around the device. If water or other liquids get inside 
this unit, a fire or electric shock may result. Immediately 
disconnect the power plug, and contact the store where 
you purchased this unit.



p Do not insert foreign objects. If water or metal objects 

get inside this unit, a fire or electric shock may result. 
Immediately disconnect the power plug, and contact the 
store where you purchased this unit.



p Do not disassemble this product. Otherwise, it may cause 

fire or electric shock.



p Do not do anything that may damage the AC cord or 

the AC plug. Do not damage or modify the cord, place 
it near hot tools, bend, twist, or pull it forcefully, place 
heavy objects on it, or bundle it tightly. Continuing to use 
a damaged cord may result in fire, short circuit, or electric 
shock. If the cord or plug needs to be repaired, consult 
the store where you purchased this unit.



p Do not attempt to install this unit or proceed with any 

connections during a thunderstorm. Otherwise, it may 
cause fire or electric shock.



p Stop operation immediately if the unit emits smoke, 

excessive heat or abnormal smell. These conditions can 
cause fire or electric shock. Immediately disconnect the 
power plug, and contact the store where you purchased 
this unit.



p Do not use this equipment close to an automatic control 

equipment like an automatic door fire alarm and so on. 
Radio waves from this equipment may cause the trouble 
by a malfunction for automatic equipment.



p Do not put this product close to a medical equipment. 

(Do not bring this product into operating room, intensive 
care units (ICU) and coronary care units (CCU).) Radio 
waves from this equipment may cause the trouble by a 
malfunction for medical equipment.



p Ask the store where you purchased this unit to do the 

installation work. Expertise and experience are required 
to install this unit. Otherwise, injuries or damage to this 
unit may result. Be sure to ask the store where you 
purchased this unit to perform this work.



p Do not put this product on a place with moisture or dirt. 

There is the risk of injury.



p Perform touch panel operations using only one finger. If 

two or more fingers come into contact with the panel at 
the same time, the touch panel may not operate properly.



p Do not use a ballpoint pen or other hard-tipped or sharp 

object, including fingernails, to perform touch panel 
operations.



p Do not press on the LCD display with too much force.



p Do not use any of the LCD protective films available on 

the market. (The touch panel may not operate properly.)



p The inside of the LCD display may become cloudy or 

condensation (droplets of water) may form and the 
display may not operate properly when the temperature 
changes suddenly, such as immediately after air-
conditioning or heating has been turned on. If this 
occurs, leave this unit for about one to two hours before 
attempting to use it again.

To cut the power supply
This product has no power switch. To cut the power supply,
unplug the power plug of the product from the AC outlet. If 
it is hard to unplug the power cord due to the installation 
conditions, connect the power cord of the product to the AC 
outlet via the circuit breaker of a distribution board or to the 
AC inlet socket of a power supply control unit.

Built-in backup battery
Do not expose the built-in backup battery to excessive heat, 
such as direct sunlight or fire.

Camera image update speed
The image update speed may be slower, depending on 
the network environment used, the number and setting of 
cameras, the subjects, and number of accesses.