Wilson AIR DRIVEN TUBE CLEANER Benutzerhandbuch
8
SM-135
1. Check for burrs on rotor wrench flats and remove any with a file. (Flats are apt to
burr through wrench slippage.)
2. Place dead handle of motor in a horizontal position in a vise and secure.
3. Unscrew, counter-clockwise, key 17, Rear Plug.
4. Unscrew, clockwise, (left hand thread) key 16, Seal Ring Fork.
5. Remove key 15, Seal Spring.
6. Remove key 14, Spring Washer.
7. Remove key 13, carbon-type Seal Ring, by turning clockwise, with upward
movement.
CAUTION: Do not directly pull the seal ring off as the threads of tube within
rotor will damage inner ‘O’ Ring Seal inside with resulting leak.
8. Remove keys #1, 8, 9, 10, 11, 12 and 13 as a unit by applying upward pressure
or light blows with a soft-faced hammer against the threaded end of the rotor shaft.
9. To remove key 7, Cylinder, and key 5, Wear Plate, release vise and invert body.
Cylinder and wear plate should normally slide out, assisted by a slight jar. In stub-
born cases grip cylinder internally with fingers to facilitate removal or tap out.
NOTE: Cylinder, Wear Plate and Thrust Ball Bearing, key 4, can be left within
housing assembly unless repair or replacement is required.
CAUTION: Under no circumstances remove the rotor and all parts mentioned un-
der instruction 1 to 8 as a unit at one time. Breakage of the carbon-type Seal Ring,
key 13, may occur.
burr through wrench slippage.)
2. Place dead handle of motor in a horizontal position in a vise and secure.
3. Unscrew, counter-clockwise, key 17, Rear Plug.
4. Unscrew, clockwise, (left hand thread) key 16, Seal Ring Fork.
5. Remove key 15, Seal Spring.
6. Remove key 14, Spring Washer.
7. Remove key 13, carbon-type Seal Ring, by turning clockwise, with upward
movement.
CAUTION: Do not directly pull the seal ring off as the threads of tube within
rotor will damage inner ‘O’ Ring Seal inside with resulting leak.
8. Remove keys #1, 8, 9, 10, 11, 12 and 13 as a unit by applying upward pressure
or light blows with a soft-faced hammer against the threaded end of the rotor shaft.
9. To remove key 7, Cylinder, and key 5, Wear Plate, release vise and invert body.
Cylinder and wear plate should normally slide out, assisted by a slight jar. In stub-
born cases grip cylinder internally with fingers to facilitate removal or tap out.
NOTE: Cylinder, Wear Plate and Thrust Ball Bearing, key 4, can be left within
housing assembly unless repair or replacement is required.
CAUTION: Under no circumstances remove the rotor and all parts mentioned un-
der instruction 1 to 8 as a unit at one time. Breakage of the carbon-type Seal Ring,
key 13, may occur.
DISASSEMBLY OF TP-302 AIR MOTOR
ASSEMBLY OF TP-302 AIR MOTOR
1. Place dead handle of motor in a horizontal position in a vise and secure.
2. Insert key 5, Wear Plate, into body making sure dowel groove in wear plate
lines up with dowel hole in Body, key 2, and exhaust notches match exhaust pas-
sage in the body.
3. Insert key 6, Cylinder, making sure locating pin on cylinder enters pin hole of
wear plate. (Lubricate outside of cylinder prior to assembly.)
4. Insert key 1, Rotor, long end down. (Lubricate all bearing surfaces.)
5. Insert six Rotor Blades, key 7, in slots of rotor.
2. Insert key 5, Wear Plate, into body making sure dowel groove in wear plate
lines up with dowel hole in Body, key 2, and exhaust notches match exhaust pas-
sage in the body.
3. Insert key 6, Cylinder, making sure locating pin on cylinder enters pin hole of
wear plate. (Lubricate outside of cylinder prior to assembly.)
4. Insert key 1, Rotor, long end down. (Lubricate all bearing surfaces.)
5. Insert six Rotor Blades, key 7, in slots of rotor.
5
SM-135
Key Part No.
Description
1
9182
ROTOR ASSEMBLY
2
9274
HOUSING ASSEMBLY
20597
BUSHING
3
41334
SET SCREW
4
9270
THRUST BALL BEARING
5
9272
WEAR PLATE
8
2080
ROTOR BLADE (SET OF 6)
9
7802
REAR JOURNAL
10
7602
‘O’ RING
11
7605
SEAT GASKET
12
7604
SEAL SEAT
13
7789
SCAVENGER SEAL
7625
‘O’ RING
14
7608
SPRING WASHER
15
7624
SEAL SPRING
16
7626
SEAL SPRING FORK
17
7593
REAR PLUG
18
28102
QUAD RING
19
7597
20
7661
EYE BOLT
21
7611
SPRING
22
7616
CAP SCREW
23
7614
GRIP LOCK PIN
24
7622
GRIP LOCK
25
7613
HANDLE GRIP BEARING
DEAD HANDLE
26
7615
VALVE SPRING
Qty.
1
1
1
1
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
9268
1
DOWEL PIN
6
9271
1
THRUST BUSHING
7
9273
1
CYLINDER
27
8531
1
VALVE ASSEMBLY
28
7623
1
CAM FOLLOWER PIN
29
7619
2
CAM FOLLOWER ROLL
30
7621
1
HANDLE GRIP
31
7620
1
HANDLE GRIP SPRING
32
7598
1
LIVE HANDLE ASSEMBLY
33
6685
1
STREET ELBOW