Whirlpool CGT8000XQ Installationsanweisungen

WARM START (after power failure) – A few seconds after 

power is restored, if a cycle was in progress at the time of the 

power failure, “RESELECT CYCLE” will flash in the display, 

indicating the need for a key press to restart washer or dryer.

WASHER DOOR LOCK – Prior to beginning a cycle, there is a 

door lock routine of lock/unlock/relock, then cycle begins. The 

door will remain locked until the end of a cycle or approximately 

2 minutes after a power interruption.

PRICING – After the door is opened and then closed following 

the completion of a cycle, the display indicates the cycle 

price (unless set for free operation, where the display will flash 

“SELECT CYCLE”). As coins are dropped or debit inputs arrive, 

the display will change to lead the user through the initiation  
of a cycle.

A dryer set up for “Fixed Cycle” operation can only accept 

additional time accumulated by increments equal to the length 

of a complete dry cycle. A maximum of 99 minutes may be 

purchased; no additional credit is given for coins dropped  

with 99 minutes in the display.

If the price is set to one coin 1, then accumulator pricing is  

in effect. Cycle time can be purchased one coin at a time up  

to the maximum time of 99 minutes.

A dryer set to offer “Top Off” capability will allow time to  

be added to an existing dry cycle in increments equal to the 

number of minutes of dry time per quarter (coin 1), up to 99 

minutes, regardless of the cost required to start the dryer. No 

credit is given for coins or debit inputs entered when the control 

is displaying 99 minutes.

In Enhanced Debit Mode, the top off price can be set 

independently (see VALUE OF COIN 2), and the top off time  

is calculated according to the following equation: 

top off time = 

x full cycle length 

Penny increment offset is not applied to top off purchases.

FREE CYCLES – This is established by setting the cycle price 

to zero. When this happens, “SELECT CYCLE” will appear 

rather than a cycle price. Any cycle started as a free cycle  

will automatically terminate when the door is opened.

DEBIT CARD READY – This washer/dryer is debit card ready. 

It will accept a variety of debit card systems, but does NOT 

come with a debit card reader. Refer to the debit card reader 

manufacturer for proper washer/dryer set-up. In models 

converted to a Generation 1 debit card system, debit pulses 

represent the equivalent of one coin (coin 1).

IMPORTANT: Read all instructions before operating.

Insert service switch key and turn counterclockwise.

Once a Generation 2 debit card reader is installed (according  

to the reader manufacturer’s instructions), the set-up modes 

can be changed only by inserting a set-up card (supplied by 

the reader manufacturer) into the card slot. Inserting the service 

switch key and turning will only access the service mode. 

The washer/dryer is now in set-up mode. The lower 

temperature setting buttons and the lower portion of the display 

are used to set up the digital control for the washer. The upper 

three fabric setting buttons and the upper portion of the display 

are used to set up the controls for the dryer.

The display can contain 4 numbers and/or letters and a decimal 

point on both the top and bottom display portions. These are 

used to indicate the set-up codes and related code values 

available for use in programming the washer/dryer.

1.  The lower-left (HOT) button is used to adjust the values 

associated with washer set-up codes and the upper-

left (COTTON/WHITES) button is for the dryer. Pressing 

the button will change the value by increments. Rapid 

adjustment is possible by holding the button down.

2.  The lower-middle (WARM) button will advance through the 

set-up codes. Pressing the button will advance both the 

washer and dryer to the next available set-up code. Some 

set-up codes are washer- or dryer-specific and will not be 

displayed on both the washer and dryer portions of the 

display. Holding down the lower-middle (WARM) button will 

automatically advance through the set-up codes at a rate 

faster than 1 per second.

3.  The lower-right (COLD) button is used to select or deselect 

washer options; upper-right (COLORS/DELICATES) is used 

for dryer option selection or deselection.

top off price

full cycle price