Dacor DYRP48DSNGH Installationsanweisungen

Installation Instructions

Verifying Proper Operation

Before operating the range, read the accompanying use and 

care manual completely. It contains Important safety, service and 

warranty information.
1.  Before beginning the test procedure, ensure that all cooktop 

control valves are in the 

OFF position, and all burner rings, 

burner caps, and grates are properly positioned on the 

cooktop frame. 

2.  Turn on the gas supply at the shut-off valve. Check for gas 

leaks.

3.  Turn on power to the range at the circuit breaker or fuse box.
4.  Follow the prompts on the oven’s display to set up the user 

preferences and wireless network settings.

5.  Touch the 

MENU key on the display.

6.  Touch the 

BAKE key on the display. The default bake 

temperature should appear on the display .

7.  Touch 

Start. After 3 minutes, open the door to make sure the 

air inside the oven has begun to heat.

8.  The display should show 

BAKE, and the preheating 

temperature.

9.  Touch 

CANCEL-SECURE or CANCEL RIGHT on model 

DYRP48D to stop the oven heating process.

10.  Test one of the burners by pushing the knob in and turning it 

counterclockwise to the 

HIGH position. It may take up to four 

seconds for ignition to occur, at which time the ignitor will stop 

sparking. If ignition does not occur 

within four seconds, turn off the 

knob, wait for at least five minutes 

to allow any gas to dissipate, 

then repeat the ignition test. After 

ignition, rotate the control knob 

counterclockwise from 

HIGH to 

LOW to adjust the flame height 

progressively. When the range is 

installed properly, the flame will be 

steady and quiet. It will also have 

a sharp, blue inner cone that will 

vary in length proportional to the burner size. Dacor’s Smart 

Flame™ feature reduces the flame under the grate fingers to 

increase grate life. If the range is equipped for use 

with LP gas, the ends of the flame may be yellow 

at the tips, which is normal.

11.  Turn the control knob to the 

OFF position.

12.  Repeat the ignition test for all remaining burners.
If the range does not operate properly, follow these 

troubleshooting steps:
1.  Verify that power and gas are supplied to the range.
2.  Check the electrical connections and gas supply to ensure 

that the installation has been completed correctly.

3.  Repeat the above bake test or burner ignition test.
4.  If the appliance still does not work, contact Dacor Distinctive 

Service at (800) 793-0093 ex. 2822. Do not attempt to repair 

the appliance yourself. Have the model and serial numbers 

available when you call. See page II for location.

Dacor is not responsible for the cost of correcting problems 

caused by a faulty installation.

Removing the Range for Service

1.  Turn the gas supply valve to the off position.
2.  Turn off power to the range at the circuit breaker panel or 

fuse box.

3.  Pull the range out from the wall

Reinstalling the Range After 

Service

1.  Push the range into operating position, making sure the anti-

tip bracket is engaged (see page 16).

2.  Turn on power to the range at the circuit breaker panel or 

fuse box.

3.  Turn the gas supply valve to the on position.

Installation Checklist

• 

To ensure a safe and proper installation, the following 

checklist should be completed by the installer to ensure 

that no part of the installation has been overlooked.

• 

Proper installation is the responsibility of the homeowner. 

The importance of proper installation of your Dacor range 

cannot be overemphasized.

 

□

Has the plastic coating been peeled off the outside of the 

range? Have all packaging materials been removed from 

inside the oven?

 

□

Are all leveling legs extended down to make contact with the 

floor? Is the unit level? See page 16.

 

□

Is the range secured in place with the provided anti-tip 

 

□

Is the range wired and grounded according to these 

instructions and in accordance with all applicable electrical 

codes? Has the electrical access cover been replaced? See 

 

□

Has the gas supply inlet pressure been measured to ensure 

that it does not exceed the maximums stated in these 

 

□

Is the range connected to the gas supply according to these 

instructions and in accordance with all applicable codes? 

Did the installer check the gas supply for leaks? Has the gas 

regulator cover been re-installed? See page 15.

 

□

Is the oven door properly installed according to these 

 

□

Have the burner knobs been installed in the proper locations? 

 

□

Are the burners and grates properly installed according to 

these instructions? See page 18.

 

□

Has proper operation been verified? Has the warranty 

been activated on-line or the warranty card been filled out 

completely and mailed?