Dacor DYRP48DSNGH Installationsanweisungen

Preparing for Installation

• 

If the gas or electric service provided does not meet the 

product specifications, do not proceed with the installation. 

Call the dealer, the gas supplier or a licensed electrician.

• 

Before installing the range, you must locate and secure the 

anti-tip bracket to the floor.

IMPORTANT: Within the Commonwealth of Massachusetts, this 

appliance must be installed by a licensed plumber or gas fitter.

Unpacking the Range

Unpack the parts box and verify that all required components 

have been provided. If any item is missing or damaged, please 

contact your dealer immediately. Do not install a damaged or 

incomplete appliance.

Installation Instructions

- 3 Grates
- 8 Standard burner caps 

  (4 brass, 4 porcelain)*
- 4 Standard burner rings
- 4 SimmerSear burner caps 

  (2 brass, 2 porcelain)*
- 2 SimmerSear burner rings
- 2 SimmerSear burner heads
- 2 GlideRack™ oven racks 
- 1 Standard rack
- 2 GlideRack™ 18” wide oven 

  racks (DYRP48D only)
- 1 18” wide standard oven rack  

  (DYRP48DS only)

- 6 Knobs (4 Standard,  

  2 MAX GRIDDLE)
- Anti-tip bracket with screws 

and anchors
- Meat probe
- Griddle
- Wok ring
- Stainless steel cleaner
- Literature kit
- Broiler pan/grill

*The range is supplied with two different types of burner caps 

(brass and porcelain) to suit the customer’s preference.

Installing a Downdraft Vent (Optional)

Install the downdraft vent before installing the range. See the 

installation instructions included with the downdraft vent.
IMPORTANT: The downdraft vent attaches to the narrow back 

portion of the cutout. It is self-supporting in the cutout and does 

not actually attach to the range itself.

Installing a Backguard (Optional)

Install the backguard before making the range gas and electrical 

connections. Install it according the installation instructions 

included with the backguard kit.
Approved backguard kits: 

APB36D3 3 inch high backguard for range model DYRP36DS
APB36D9 9 inch high backguard for range model DYRP36DS
APB48D3 3 inch high backguard for range model DYRP48DS
APB48D9 9 inch high backguard for range model DYRP48DS

Install the Anti-Tip Bracket and Foot

Locate the anti-tip bracket included in the parts box.

• 

Floor mounting (preferred method)

• 

Wall mounting (alternate method). Use this method if floor 

mounting is not suitable. If the front panel of range is further 

than 26 1/2” (67.3 cm) from the back wall or if the flooring is 

too thick (see Installing the Anti-Tip Bracket on the Wall), 

the wall mounting method may not be used and the floor 

mounting method must be suitable.

Installing the Anti-Tip Bracket on the Floor 

To perform its intended function, the anti-tip bracket must be 

attached as instructed to the concrete slab or wood sub-floor 

below any floor coverings (including cement board) on top. Do 

not attach the anti-tip bracket directly to floor coverings such as 

ceramic/asphalt tile or linoleum.

Four (4) plastic anchors are provided along with three sizes (4 

each) of #8 or #12 Phillips head screws for attaching the anti-

tip bracket to the floor. Use both the anchors and four (4) of the 

screws when attaching the bracket to a concrete sub-floor. Do not 

use the provided anchors when attaching to a wood sub-floor.
    continued...

Sub-floor

Screws attached to  

sub-floor below floor 

covering

Anti-tip

bracket

Floor 

covering

Concrete anchors shown, do

not use for wood sub-floor