Dacor DYRP48DSNGH Installationsanweisungen

Cabinet Layout

• 

All maximum and minimum dimensions and clearances 

shown in the diagrams below must be maintained for safe 

operation.

• 

Check the location where the range is to be installed. It 

should be placed away from drafts that may be caused by 

doors, windows and heating and air conditioning outlets. 

• 

To reduce the risk of fire or personal injury from reaching over 

a hot appliance, avoid cabinet installations directly above the 

range. If cabinet storage is to be provided, the risk can be 

reduced by installing a range hood that projects horizontally a 

minimum of 5 inches beyond the bottom of the cabinets.

• 

The range may be installed flush to the rear wall. Dacor 

strongly recommends installing a non-combustible material 

on the rear wall above the range and up to the vent hood or 

installation of a backguard. It is not necessary to install non-

combustible materials behind the range below the countertop 

height. Any openings in the wall behind the appliance or in 

the floor underneath it must be sealed.

Gas and Electrical Service

• 

The shaded area shown below denotes the location of the 

gas inlet and the electrical junction box/receptacle. This is 

the recommended location. For replacement purposes, the 

location of the existing utilities may be utilized provided they 

do not interfere with the sides or rear of the range. Check 

local building codes for permissible gas valve locations.

• 

An external manual shut-off valve must be installed between 

the gas inlet and the range for the purpose of turning on or 

shutting off gas to the appliance.

• 

Access to the gas shut-off valve when the unit is installed.

• 

Access to the remote circuit breaker panel/fuse box, when the 

range is in place.

• 

The gas supply piping and shut-off valve, and the electrical 

junction box/receptacle must be located so they do not 

interfere with the range when it is installed.

• 

The junction box and gas shut off valve must be located 

so that the range can be pulled out for service while the 

appliance remains connected.

Note 2

F

G

2

 Cabinet/countertop depth is at discretion of customer but 

cabinet face MUST NOT protrude further than rear of front 

panel, see product dimensions.

3

 Consult local code for exact location requirements.

1

 Vertical from range grate level to combustible overhead 

surface; if installing an overhead vent hood, also check  

hood specifications for minimum required clearances. 

4

 Vertical from grate level to combustible surface.

Non-combustible 

surface along back wall 

recommended

10” (25.4 cm) min.

to combustible side

walls above the range

(both sides)

30” (76.2  cm)

min.

1

37 1/2” 

(95.3 cm)

max.

13” (33.0 cm)

max.

5

15” (38.1 cm)

min.

4, 5

5

 This specification does not apply for cabinets more 

than a horizontal distance of 10” (25.4 cm) from the 

edge of the range.

Suggested 

location of 

utilities

 

3

Grate 

level

G

10" (25.4 cm) min.
to combustible side
walls above the range
(both sides)

non-combustible

rear wall recommended

Backsplash

3/8" (1.0 cm)

Min. flat countertop

overhang

H

3” (7.6 cm)

Note 2

Cutout tolerances: +1/16” (+1.6 mm), -0 

unless otherwise stated

DYRP36D[-C-]S 42” (106.7 cm)* 

36” (91.4 cm)**

36” 

(91.4 cm)**

33 1/2” 

(84.8 cm)

DYRP48D[-C-]S 54” (137.2 cm)* 

48” (121.9 cm)**

48” 

(121.9 cm)**

43 1/2” 

(110.2 cm)

* Recommended ** Minimum

DYRP36D[-C-]S

ERV36-ER

DYRP48D[-C-]S

ERV48-ER

IMPORTANT: See the downdraft installation instructions 

for duct and electrical installation requirements. Use only 

the Dacor downdraft vent models specified above.

Planning the Installation