Thermador PRD304GHU Installationsanweisungen
English 10
the bolts, the range must be lifted and removed from
the pallet.
the pallet.
Important:
DO NOT lift the range by the oven door handle, as this may
damage the door hinges and cause the door to fit
incorrectly to the oven cavity.
damage the door hinges and cause the door to fit
incorrectly to the oven cavity.
Note:
Leave adhesive-backed foam layer over brushed-metal
surfaces, to protect finish from scratches, until the range is
installed in final position.
Leave adhesive-backed foam layer over brushed-metal
surfaces, to protect finish from scratches, until the range is
installed in final position.
•
Due to the weight, a dolly with soft wheels should be
used to move this unit. The weight must be supported
uniformly across the bottom (See Figure 5).
used to move this unit. The weight must be supported
uniformly across the bottom (See Figure 5).
•
After transporting the range by dolly close to its final
location, the range can be tipped back and supported
on the rear legs while the dolly is carefully removed.
THE FLOOR UNDER THE LEGS SHOULD BE
location, the range can be tipped back and supported
on the rear legs while the dolly is carefully removed.
THE FLOOR UNDER THE LEGS SHOULD BE
PROTECTED BEFORE PUSHING THE UNIT INTO
POSITION. The anti-tip device must be installed (Step
4), gas and electrical connections should be made
(Step 5 and Step 6), and the backguard installed (Step
7) before the range is placed in its final position.
POSITION. The anti-tip device must be installed (Step
4), gas and electrical connections should be made
(Step 5 and Step 6), and the backguard installed (Step
7) before the range is placed in its final position.
•
For proper performance, the range must be level.
(This is very important for all products that have the
griddle feature.) The range is leveled by adjusting the
legs with a wrench.
(This is very important for all products that have the
griddle feature.) The range is leveled by adjusting the
legs with a wrench.
•
Replace the kick panel. It is important that the
screws retaining the kick panel are secure to
prevent accidental access to hot surfaces.
screws retaining the kick panel are secure to
prevent accidental access to hot surfaces.
•
Ensure that the burner caps are correctly seated on the
burner bases of the range's cooktop.
burner bases of the range's cooktop.
•
Remove all tape and packaging before using the
appliance. Destroy the packaging after unpacking the
appliance. Never allow children to play with packaging
material.
appliance. Destroy the packaging after unpacking the
appliance. Never allow children to play with packaging
material.
Important:
DO NOT lift the range by the oven door handle, as this may
damage the door hinges and cause the door to fit
incorrectly to the oven cavity.
damage the door hinges and cause the door to fit
incorrectly to the oven cavity.
Griddle Tilt Adjustment (Not All Models)
If the range is equipped with an electric griddle, check the
griddle frame adjustment by pouring two tablespoons of
water on the back of the griddle plate. The water should
slowly roll into the grease tray. If not, adjust the two screws
under the back of the frame. Start with one half turn
counterclockwise (CCW) of the screws. Further adjustment
should be made by one-quarter turn until water slowly flows
into the grease tray.
griddle frame adjustment by pouring two tablespoons of
water on the back of the griddle plate. The water should
slowly roll into the grease tray. If not, adjust the two screws
under the back of the frame. Start with one half turn
counterclockwise (CCW) of the screws. Further adjustment
should be made by one-quarter turn until water slowly flows
into the grease tray.
Chart A
30"
Range
36"
Range
48"
Range
Shipping Weight
351 lbs.
371 lbs.
499 lbs.
Weight without
packing materials
packing materials
228 lbs.
270 lbs.
403 lbs.
Without doors,
burner caps, front
kick panel and oven
racks
burner caps, front
kick panel and oven
racks
185 lbs.
221 lbs.
318 lbs.
Figure 4: Removal of the Four (4) Shipping Bolts
Pallet
Figure 5: Dolly Positioning
Range
Must be
Uniformly
Supported
by Braces
Provided
on Bottom
of Range
Must be
Uniformly
Supported
by Braces
Provided
on Bottom
of Range