Whirlpool WEE730H0D Installationsanweisungen

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.

Check that all parts are included. 

■

10-32 hex nuts (attached to terminal block) (3)

■

Direct wire lugs (3)

■

#10 x 1

⁵⁄₈" (4.1 cm) screws (for mounting anti-tip bracket) (2)

■

Anti-tip bracket (inside oven cavity)

Anti-tip bracket must be securely mounted to the back wall or 
floor. Thickness of flooring may require longer screws to 
anchor bracket to subfloor. Longer screws are available from 
your local hardware store.

■

If using a power supply cord kit:

■

A UL listed power supply cord kit marked for use with ranges. 
The cord should be rated at 250 volts minimum, 40 amps or 
50 amps that is marked for use with nominal 1

³⁄₈" (3.5 cm) 

diameter connection opening and must end in ring terminals 
or open-end spade terminals with upturned ends.

■

A UL listed strain relief.

Check local codes. Check existing electrical supply. See the 
appropriate “Electrical Requirements” section.

It is recommended that all electrical connections be made by a 
licensed, qualified electrical installer.

To purchase these or any other accessories, please reference the 
“Accessories” section of the User Guide for contact information.

■

⁵⁄₈" (1.7 cm) White - Order Part Number W10675027

⁵⁄₈" (1.7 cm) Black - Order Part Number W10675026

⁵⁄₈" (1.7 cm) Stainless Steel - Order Part Number W10675028
1

¹⁄₈" (2.9 cm) White - Order Part Number W10731885

1

¹⁄₈" (2.9 cm) Black - Order Part Number W10731886

1

¹⁄₈" (2.9 cm) Stainless Steel - Order Part Number 

W10731887

■

Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number 
W10655450

IMPORTANT: Observe all governing codes and ordinances.

■

It is the installer’s responsibility to comply with installation 
clearances specified on the model/serial/rating plate. The 
model/serial/rating plate is located behind the oven door on 
the top right-hand side of the oven frame.

■

The range should be located for convenient use in the 
kitchen.

■

Recessed installations must provide complete enclosure of 
the sides and rear of the range.

■

To eliminate the risk of burns or fire by reaching over the 
heated surface units, cabinet storage space located above 
the surface units should be avoided. If cabinet storage is to 
be provided, the risk can be reduced by installing a range 
hood or microwave hood combination that projects 
horizontally a minimum of 5" (12.7 cm) beyond the bottom of 
the cabinets.

■

All openings in the wall or floor where range is to be installed 
must be sealed.

■

Tape measure

■

Flat-blade screwdriver

■

Phillips screwdriver

■

Level

■

Hand or electric drill

■

Wrench or pliers

■

Marker or pencil

■

Masking tape

■

¼" (6.4 mm) drive ratchet

■

¼" (6.4 mm) nut driver 

■

³⁄₈" (9.5 mm) and ⁵⁄₁₆" (8 mm) 
nut driver

■

¹⁄₈" (3.2 mm) drill bit (for 
wood floors)

■

Tin snips or large wire 
cutters (for cutting ground 
strap if necessary)

2

3