BlueStar RNB606GV1 Handbuch
9
pressure. The regulator used on this unit will
withstand a maximum input pressure of 1/2 psi,
(12" WC). If the incoming line pressure is
higher than this maximum rating, a step-down
regulator is required upstream of the unit's
factory-installed regulator.
withstand a maximum input pressure of 1/2 psi,
(12" WC). If the incoming line pressure is
higher than this maximum rating, a step-down
regulator is required upstream of the unit's
factory-installed regulator.
The appliance and its individual shut-off valve
must be disconnected from the gas supply
piping system during any pressure testing of
the homes’ gas line system at pressures in
excess of 1/2 psig, (3.5kPa).
piping system during any pressure testing of
the homes’ gas line system at pressures in
excess of 1/2 psig, (3.5kPa).
The appliance must be isolated from the gas
supply piping system by closing its individual
shut-off valve during any testing of the homes’
gas system at pressures equal to or less than 1/2
psig, (3.5kPa).
shut-off valve during any testing of the homes’
gas system at pressures equal to or less than 1/2
psig, (3.5kPa).
3. Rigid connections: Incoming gas is brought
from the inlet pipe at the rear of the unit to the
pressure regulator, then through the upper
manifold for distribution. The only connection
necessary is from the service line, through the
installer-supplied shut-off valve, to this inlet
pipe.
pressure regulator, then through the upper
manifold for distribution. The only connection
necessary is from the service line, through the
installer-supplied shut-off valve, to this inlet
pipe.
Be sure to double check any installer-supplied
pipes and fittings, and/or blow compressed air
through them to clean out dirt particles,
threading chips, or other foreign matter before
connecting the unit to the service line. Such
particles will clog orifices when gas pressure is
through them to clean out dirt particles,
threading chips, or other foreign matter before
connecting the unit to the service line. Such
particles will clog orifices when gas pressure is
applied. Service to clean such clogs is not
covered by the warranty.
covered by the warranty.
Check all gas connections for leaks using a
soapy solution before lighting any pilots. DO
NOT USE AN OPEN FLAME TO CHECK
FOR LEAKS! Using an open flame to check a
new connection is not only dangerous, but it
will also miss small leaks that a soapy solution
would detect.
NOT USE AN OPEN FLAME TO CHECK
FOR LEAKS! Using an open flame to check a
new connection is not only dangerous, but it
will also miss small leaks that a soapy solution
would detect.
4. Flexible connections: If the unit is to be
installed with flexible couplings and/or a
"quick-disconnect," the installer must use a
commercially approved AGA Design Certified
flexible connector of at least 1/2" NPT, in
compliance with ANSI Z21.41.
"quick-disconnect," the installer must use a
commercially approved AGA Design Certified
flexible connector of at least 1/2" NPT, in
compliance with ANSI Z21.41.
In Canada, a connector complying with CAN
16.10 - 88, and a quick disconnect device
complying with CAN 16.19M - 79 must be
installed with a strain relief device to guard
against the transmission of strain to the
connector.
complying with CAN 16.19M - 79 must be
installed with a strain relief device to guard
against the transmission of strain to the
connector.
5.Air shutter adjustments are the responsibility of
the installer, and are not covered by warranty.
Burners are preset at the factory and may need
fine-tuning by the installer.
Burners are preset at the factory and may need
fine-tuning by the installer.
GAS CONVERSION
Any field gas conversions will automatically void the manufacturers warranty!! Gas conversions
should only be performed by a licensed professional to assure a complete and safe conversion. Please
contact your distributor for additional information regarding gas conversion.
should only be performed by a licensed professional to assure a complete and safe conversion. Please
contact your distributor for additional information regarding gas conversion.
WARNING:
IN ORDER TO AVOID A FIRE OR EXPLOSION, CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH; PRECAUTION MUST BE TAKEN WHEN PERFORMING A CONVERSION BY ENSURING
THAT THE VALUES IN THE GAS PRESSURE CHARTS ARE EMPLOYED WHERE APPLICABLE.
THAT THE VALUES IN THE GAS PRESSURE CHARTS ARE EMPLOYED WHERE APPLICABLE.
For additional information regarding field conversions, contact your distributor/dealer.