Dacor RNR30NC Installationsanweisungen

Installation Instructions

Verify the Package Contents

Verify that all the components below have been provided. If 

any item is missing or damaged, please contact your dealer 

immediately. Do not install a damaged or incomplete appliance. 

Make sure that you have everything necessary to ensure proper 

installation before proceeding.
•  Use and care manual
•  Anti-tip bracket with screws and anchors
•  Oven racks (2) GlideRack type, (1) standard type
•  Razor blade scraper
•  Dacor Cooktop Cleaning Cream

Installing the Anti-Tip Bracket

Locate the anti-tip bracket included in the parts box.

• 

Floor mounting (preferred method).

• 

Wall mounting (alternate method). Use this method if floor 

mounting is not suitable. If any of the conditions below exist, 

then the wall mounting method cannot be used and the floor 

mounting method must be suitable.

◊  The wall contains metal stud mounting materials that 

interfere with the anti-tip bracket mounting screws.

◊  The front panel of the range is further than the maximum 

distance from the back wall stated on page 9.

◊  A downdraft vent is installed.
◊  The flooring is too thick (see Installing the Anti-Tip 

Bracket on the Wall).

To perform its intended function, the anti-tip bracket must be 

attached as instructed to the concrete slab or wood sub-floor 

below any floor coverings (including cement board) on top. Do 

not attach the anti-tip bracket directly to floor coverings such as 

ceramic/asphalt tile or linoleum.

Four (4) plastic anchors are provided along with three sizes  

(4 each) of #8 or #12 Phillips head screws for attaching the anti-

tip bracket to the floor. Use both the anchors and four (4) of the 

#8 screws when attaching the bracket to a concrete sub-floor. Do 

not use the anchors when attaching to a wood sub-floor.

1.  Determine the location of the range center line and front 

panel when the range is in its final position based on the 

Product Dimensions on page 4, and the actual cabinet/ 

cutout dimensions used for the installation.

2.  Determine the required position of the anti-tip bracket, 

based on the diagram on the facing page. Mark the four (4) 

mounting hole locations on the floor with a pencil.

3.  Determine the screw size required. The minimum full thread 

depth (portion of screw threaded into wood/slab) for wood 

is 3/8” (1 cm) and 5/8” (1.6 cm) for concrete. See the table 

below to select the correct screw size.

Concrete or wood sub-floor, no floor 

covering over top

#8 x 1” *

Concrete or wood sub-floor, floor 

covering up to 1/4” thick

#8 x 1” *

Concrete or wood sub-floor, floor 

covering over 1/4” and up to 1/2” thick

#8 x 1 1/4” *

Wood sub-floor, floor covering over 

1/2” and up to 1 3/16” thick

#12 x 1 3/4” *

Concrete sub-floor under floor covering  

over 1/2” thick

Must be purchased 

separately **

Wood sub-floor, floor covering  

over 1 3/16” thick

Must be purchased 

separately **

* Included with range
** Not included. Determine length based on step 3.

• 

Drill four (4) 3/8” diameter countersink holes through any 

existing floor covering down to the concrete slab below. 

• 

Drill the 4 holes for the anchors 1 1/4” (3.2 cm) deep into the 

concrete slab using a 3/16” masonry bit. This hole length is 

longer than the anchor, but is required for proper installation. 

Clear the holes of dust and any other material. Tap each 

anchor into the hole until the anchor top is flush with the top 

of the concrete slab. Position the anti-tip bracket holes over 

the anchor holes. Insert the screws through the four (4) holes 

in the base of the bracket and thread them into the anchors. 

Be sure the screw threads fully engage the anchor body. 

Tighten the screws into place. 

• 

If there is ceramic, asphalt or other hard floor covering over 

the wood below, drill four (4) countersink holes to allow 

access to the wood below for drilling pilot holes.

• 

Drill four (4) pilot holes into the wood floor using a drill bit 

(1/16” dia. for #8 screws, 1/8” dia. for #12 screws). Position 

the anti-tip bracket holes over the holes in the floor. Insert the 

screws into the wood and tighten into place.

1.  To use the wall mount option, the range front panel must not 

be more than 26 1/4” from the wall and the bracket screws 

must be able to thread into the base plate inside the wall 

behind. The notches on the sides of the bracket indicate the 

minimum required height of the base plate inside the wall and 

that any floor covering is not too thick for proper screw thread 

engagement.

Screws attached 

to sub-floor below 

floor covering

Sub-floor

Concrete 

anchors shown, 

do not use for 

wood sub-floor

Floor 

covering

Anti-tip 

bracket