Thermador PRG366JG Benutzeranleitung
English 2
36" Gas Models:
120 volts, 60 Hz., 15 Amp electrical circuit required.
36” model with electric griddle - 20 Amp circuit required.
36” model with electric griddle - 20 Amp circuit required.
48" Gas Models with electric griddle:
120 volts, 60 Hz., 20 Amp electrical circuit required.
It is recommended that a dedicated circuit servicing this
appliance be provided. See Installation Instructions for
electrical requirements and grounding instructions.
appliance be provided. See Installation Instructions for
electrical requirements and grounding instructions.
The use of gas cooking appliances results in the production
of heat and moisture.
of heat and moisture.
It is the personal responsibility and obligation of you, the
user, to have this appliance connected to the electrical
power supply by a qualified electrician, in accordance with
the National Electrical Code and/or applicable local codes
and ordinances.
user, to have this appliance connected to the electrical
power supply by a qualified electrician, in accordance with
the National Electrical Code and/or applicable local codes
and ordinances.
Safety Codes and Standards
•
UL 858, The Standard for the Safety of Household
Electric Ranges
Electric Ranges
•
ANSI Z21.1, The American National Standard for
Household Cooking Gas Appliances
Household Cooking Gas Appliances
•
CAN 1-1.1-M81, Domestic Gas Ranges
•
CSA C22.2 No. 61, Household Cooking Ranges
Check your local building codes for the proper method of
installation. In the absence of local codes, this unit should
be installed in accordance with the National Fuel Gas Code
No. Z223.1 current issue and the National Electrical Code
ANSI/NFPA No. 70 current issue or the Can - B149
Installation Codes for Gas Burning Appliances and C22.1
Canadian Electrical Code Part 1.
installation. In the absence of local codes, this unit should
be installed in accordance with the National Fuel Gas Code
No. Z223.1 current issue and the National Electrical Code
ANSI/NFPA No. 70 current issue or the Can - B149
Installation Codes for Gas Burning Appliances and C22.1
Canadian Electrical Code Part 1.
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
WARNING:
To avoid possible burn or fire hazard, a back guard
designed specifically for this range must be installed
whenever the range is used.
designed specifically for this range must be installed
whenever the range is used.
CAUTION:
The high shelf can get very hot! DO NOT place the
following items on top of the high shelf:
following items on top of the high shelf:
•
plastics or containers that can melt
•
flammable items
•
a total load over 30 lbs. (13.6 kg)
WARNING:
ALWAYS DISCONNECT THE ELECTRICAL PLUG
FROM THE WALL RECEPTACLE BEFORE
SERVICING THIS UNIT.
FROM THE WALL RECEPTACLE BEFORE
SERVICING THIS UNIT.
CAUTION:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE CONNECTED TO A PROPERLY GROUNDED AND
POLARIZED ELECTRICAL POWER SUPPLY.
BE CONNECTED TO A PROPERLY GROUNDED AND
POLARIZED ELECTRICAL POWER SUPPLY.
WARNING:
IN CASE OF AN ELECTRICAL FAILURE
If for any reason a gas control knob is turned ON and
there is no electrical power to operate the electronic
igniters on the range's cooktop STAR
there is no electrical power to operate the electronic
igniters on the range's cooktop STAR
®
burners, turn
OFF the gas control knob and wait 5 minutes for the
gas to dissipate before lighting the STAR burner
manually.
gas to dissipate before lighting the STAR burner
manually.
To light the STAR burners manually, carefully hold a
lighted match to the STAR burner ports and turn the gas
control knob to HI
lighted match to the STAR burner ports and turn the gas
control knob to HI
.
During a power failure
,
you can use the standard
cooktop
STAR
burners, but each must be lit with a
match.
DO NOT attempt to light the two left XLO
®
STAR
burners and two right XLO STAR burners manually.
These STAR burners are equipped with the ExtraLow
These STAR burners are equipped with the ExtraLow
®
feature and cannot be lit manually.