Citizen Systems CL-S700 Benutzerhandbuch
2
Printer Operation
38
Mode Settings
[Datamax Emulation]
[Datamax Emulation]
Top Menu
Sub Menu
Default
Menu
Remarks
Metric/Inch
Inch
Inch
Sets the units.
[Metric/Inch Sel]
mm
Max Media Length
10.00 inch
1.00 to 50.00 inch
Sets the maximum media length.
[Max Media Len]
254.0 mm
25.4 to 1270.0 mm
Settings Lock
Off
On
Prevents a command changing the set value.
Off
Keyboard Lock
Off
On
Prevents a change by a key operation.
Off
Note: Hold down the Menu Key for at least 4
seconds to enter the Menu Setup Mode when
setting the “On” menu.
seconds to enter the Menu Setup Mode when
setting the “On” menu.
Control Code
STD
STD
Switches command mode of DMX mode.
ALT
Emulation Select
DM4 or ZPI2*
DM4
Selects DataMax/Zebra compatibility
[Emulation Sel]
DMI
DM4: DataMax 400
DPP
DMI: DataMax IClass
ZPI2
DPP: DataMax Prodigy Plus
ZPI2: Zebra 2844Z
ZPI2: Zebra 2844Z
Emulation Auto
On
On
Setting emulation (Datamax/Zebra) auto
Detect
Off
detection.
[Emulation Auto]
After Print
AutoConfigure
On
On
Automatically configures optional devices.
[Auto Config]
Off
On .... AutoConfigure enabled (Regardless of
whether Function Select is set, if a
peeler or cutter is installed, each mode
is set automatically.)
peeler or cutter is installed, each mode
is set automatically.)
Off ... AutoConfigure disabled (A peeler of
cutter is installed, but to not operate
the peeler or cutter, turn it Off and the
operation is selected by
Function Select.)
the peeler or cutter, turn it Off and the
operation is selected by
Function Select.)
Function Select
Tear
Off
Selects the operation when the
[Function Sel]
Tear
AutoConfigure is set to Off. Designates the
Peel On**
paper position based on each option. The
Cut On***
operation of this device is enabled during
selection. At the same time, the parameters of
the f command of Prodigy Plus are emulated
for each optional device.
selection. At the same time, the parameters of
the f command of Prodigy Plus are emulated
for each optional device.
Cutter Action
Backfeed
Backfeed
Sets the cutter action.
Through
With the optional AutoConfigure On, printing
is executed only when the cutter is installed
or only when Cut is selected by Function
Select.
Backfeed is always set after cutting.
Through is set at the rear end of sheets 1 to
n-1 when the number of copies = n, and the
rear end of the final page of single sheet and
the copy is backfeed.
is executed only when the cutter is installed
or only when Cut is selected by Function
Select.
Backfeed is always set after cutting.
Through is set at the rear end of sheets 1 to
n-1 when the number of copies = n, and the
rear end of the final page of single sheet and
the copy is backfeed.
Paper Position
0.00 inch
Peel/Cut/Tear Off
Adjusts the stop position. It is based on the
0.00 mm
0.00 to 2.00 inch
inch/millimeter setting. There are initial
0.0 to 50.8 mm
values of the stop position for each device
Peel/Cut/Tear On
set above, and later, relative values are set.
-1.00 to 1.00 inch
-25.4 to 25.4 mm
-25.4 to 25.4 mm
*
The factory default setting of the Emulation Select will be different depending on the destination of the country.
** Only when peeling option is mounted.
*** Only when cutter is mounted.