Samsung RF4287HABP Benutzerhandbuch
06_
setting up
•
Do not install the refrigerator where the
temperature will go below 50ºF (10ºC).
temperature will go below 50ºF (10ºC).
•
Do not locate the refrigerator where it may
become wet.
become wet.
When moving your refrigerator
To prevent fl oor damage, be sure the front
adjusting legs are in the up position (above
the fl oor).
Refer to ‘Adjusting the doors’ in the manual
(on page 9).
adjusting legs are in the up position (above
the fl oor).
Refer to ‘Adjusting the doors’ in the manual
(on page 9).
FLOORING
For proper installation, this refrigerator must be placed
on a leveled surface of hard material that is the same
height as the rest of the fl ooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 359lbs (165kg). To protect the fi nish
of the fl ooring, cut a large section of the cardboard
carton and place it under the refrigerator where you
are working. When moving a refrigerator, you need
to pull and push it straight forwards or back. Do not
wiggle it from side to side.
on a leveled surface of hard material that is the same
height as the rest of the fl ooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 359lbs (165kg). To protect the fi nish
of the fl ooring, cut a large section of the cardboard
carton and place it under the refrigerator where you
are working. When moving a refrigerator, you need
to pull and push it straight forwards or back. Do not
wiggle it from side to side.
ACCESSORIES AND REQUIRED
TOOLS
TOOLS
The following accessories are included with your
refi gerator:
refi gerator:
Hex wrench
Hex wrench
Fastener
Fastener
Required Tools (Not provided)
You need the following tools to complete the
installation of your refi rgerator:
installation of your refi rgerator:
Philips screwdriver
Philips screwdriver
(+)
(+)
Flat-blade
Flat-blade
screwdriver (-)
screwdriver (-)
Socket wrench
Socket wrench
(10mm)
(10mm)
Pliers
Pliers
Allen wrench (3/16”) (5mm)
Allen wrench (3/16”) (5mm)
REMOVING THE REFRIGERATOR
DOORS
DOORS
Some installations require door removal to transport
the refrigerator to its fi nal location. Do not remove the
door/drawer if you don't need to. If you do not need
to remove the refrigerator doors, go to Adjusting the
Level on page 8. If you need to remove the doors.
continue below.
Before removing the door/drawer, make sure you read
the following items:
the refrigerator to its fi nal location. Do not remove the
door/drawer if you don't need to. If you do not need
to remove the refrigerator doors, go to Adjusting the
Level on page 8. If you need to remove the doors.
continue below.
Before removing the door/drawer, make sure you read
the following items:
Disconnect power to the refrigerator before
removing the door or drawer.
removing the door or drawer.
• Be careful not to drop, damage or scratch
the door/drawer while removing them.
•
Be careful not to get injured while removing the
door/drawer.
door/drawer.
•
Reattach the door/drawer properly to avoid:
-
Moisture from air leakage.
-
Uneven door alignment.
-
Wasting energy due to improper door seal.
Flat-blade
Flat-blade
screw driver(-)
screw driver(-)
screw driver(-)
Control Lever
Control Lever
CAUTION
WARNING
DA68-01922A.indb 06
DA68-01922A.indb 06
2013.3.4 1:32:32 PM
2013.3.4 1:32:32 PM