Fisher & Paykel 88388 EC120DXV1 Merkblatt

2

2

3

5

6

7

8

9

10

4

PLAN VIEW OF SUPPORT FRAME

FRONT FACE OF CANOPY

Before drilling any holes check that the area behind 
the surface to be drilled is clear of any electrical 
cables, pipes etc.  Fixing to a solid joist or 50mm 
deep truss is recommended. 
Whenever possible protect the hob top with 
cardboard or the like.

 

1. 

Before commencement unpack the canopy hood 

and check that it functions correctly. 

2. 

Use a plumb line to mark the centre of the 

cooking surface on the ceiling. 

3. 

Using the ceiling bracket as a template mark the 

four holes on the ceiling.  Ensure that the ceiling 
bracket front edge is parallel with the bench top 
and that the plumb line mark is central to the four 
mounting screw holes. 

4. 

Drill holes in the ceiling at the points marked. 

a. 

When fitting to a 50mm truss drill a pilot 

hole through the ceiling and into the truss. 

b. 

If securing to any other ceiling type please 

use appropriate fasteners and follow their 
instructions of use carefully. 

5. 

For the ducting mark out and cut a Ø170mm hole 

in the ceiling. 

6. 

Fix the ceiling bracket to the ceiling using the 

screws supplied. 

7. 

Using duct tape secure the ducting to the top of 

the motor housing.  Solid ducting, galvanized or 
plastic is recommended.  Use flexi ducting only 
in difficult installations and if used ensure that it 
is pulled tight.  The smoother, straighter and 
shorter the ducting the quieter and more efficient 
the canopy hood will perform.  Tape the power 
plug to the top of the ducting, this will enable 
easy access to the plug after installation. 

8. 

Mount the first set of four angle brackets on the 
canopy.  Use eight self tapping screws, one per 
side per corner. 

9. 

Determine the installed height of the canopy and attach the second set of four angle brackets to the 

first to achieve this height. Secure with eight self tapping screws, one per side per corner. 

10.  Strip the plastic protective film off the two chimney pieces and place these over the corners.  The 

lower chimney will rest on top of the canopy hood and the upper chimney will be extended and 
secured to the ceiling bracket.  To ensure that the upper chimney does not slip inside the lower 
chimney, secure it so that the upper chimney is showing.  Duct tape or placing two screws/nails 
through the upper chimney securing holes will do this. 

11.  Offer the canopy hood, angle brackets, chimneys and ducting up to the ceiling bracket and secure in 

place with eight screws provided, one per side per corner.  The dimension between the filters and the 
cooking surface should be in line with those suggested in the ‘height of canopy hood’ section.  An 
additional person will be required for this operation or a simple support frame manufactured to the 
correct dimensions will aid assembly of the Designer Island canopy hood. 

12.  Finish assembling the ducting ensuring the path is as short, straight and smooth as possible. 
13.  Connect to the power supply and switch on the power using switch/socket outside the canopy hood. 
14.  Slide the upper chimney piece up to the ceiling and secure in place with four screws supplied. 

 

For recirculation do not cut the 170mm hole into the ceiling and purchase the charcoal filters and recirculation 
kit 1744.  The recirculation kit must be used to channel the air to the top of the flue.  For other accessories parts 
and service please contact your local supplier or approved service agent. 

 

The manufacturer is not liable for any damage caused by not following these instructions. 
Particular care must be taken with the grease filters which must be periodically cleaned (at least 
every two months).  Remove the grease filters and wash them either by hand in hot soapy water or 
in the dishwasher using mild detergent.  Note: some discolouration of the frame may occur.  
Caution:  Never use abrasive or oil based liquid cleaners.  To clean the stainless steel and glass 
components of the canopy hood use mild detergent and warm water.  In areas of high humidity and 
coastal environments cleaning should be carried out frequently. 
For accessories, parts and service, please contact your local supplier (refer to the warranty certificate). 

 

(

Halogen bulb 12 Volts/20 Watt

1.  Switch off the power to the canopy hood. 
2.  Use a small bladed screwdriver to prise off the light cover taking care not to  

 

damage the surrounding material. 

3.  Remove the defective bulb from the canopy hood. 
4.  Replace with a new bulb using a cloth.  Do not touch the bulb with fingers. 

5. 

Snap the cover back into place.

 

•  This canopy hood is not intended for use by young children or infirm persons without 

supervision. 

•  Young children should be supervised to ensure that they do not play with the canopy hood. 

•  There shall be adequate ventilation of the room when the canopy hood is used at the same time 

as appliances burning gas or other fuels.  (A partial vacuum in the room could result in too high 
a concentration of gas in the air). 

•  You must read the details concerning the method and frequency of cleaning. 

•  There is a fire risk if cleaning is not carried out in accordance with the instructions. 

•  Do not flambé under the canopy hood. 

•  Exhaust air must not be discharged into an existing flue which is used for exhausting fumes 

from appliances burning gas or other fuels. 

•  The minimum distance between the hob surface and the filters of the canopy hood shall be 

600mm (650mm if installed over a gas hob). 

•  Attention should be given to ensure that any applicable regulations concerning the discharge of 

exhaust air is fulfilled. 

•  If the supply cord of this equipment is damaged it must only be replaced by the manufacturer, its 

service agent or similarly qualified person in order to avoid a hazard. 

 

 

Electrical Rating: 

 

310W (1.28 A) 
Max at 240V 50Hz 

Manufactured for 

 

 

By: 

Robinhood Ltd 

6 Zelanian Drive, East Tamaki 

Auckland, New Zealand 

ISO9001 Certified 

104923 issue A 

ECN 06 037