Panasonic NV-DS50A Benutzerhandbuch
57
5
Rewind the tape.
≥The tape automatically stops approximately at
the position where the counter was set to zero.
Stopping editing automatically during audio
dubbing
dubbing
1
Set [DISPLAY SETUP] >> [C.DISPLAY]
>> [MEMORY].
>> [MEMORY].
2
Reset the Tape Counter to zero at the
position where you want to stop
editing.
position where you want to stop
editing.
3
Play back the still picture where you
want to start audio dubbing.
want to start audio dubbing.
4
Start audio dubbing.
(
l
≥Audio dubbing automatically stops at the
position where the counter was set to zero.
ª Owner ID
You can register your name and address in your
Movie Camera to identify the owner.
Movie Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >> [OTHER
FUNCTIONS] >> [OWNER ID SET] >>
[ON].
FUNCTIONS] >> [OWNER ID SET] >>
[ON].
≥The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial to select
[PIN NUMBER] and press the [PUSH]
Dial to input desired numbers.
[PIN NUMBER] and press the [PUSH]
Dial to input desired numbers.
3
Turn the [PUSH] Dial to select numbers
and press the [PUSH] Dial to enter
them.
and press the [PUSH] Dial to enter
them.
≥You can input 4 digits.
4
Press the [
∫
] Button.
5
Repeat Steps 2–4 to input desired
characters for [NAME] and
[POSTCODE].
characters for [NAME] and
[POSTCODE].
≥You can input up to 12 characters in [NAME],
and up to 11 characters in [POSTCODE].
6
Press the [
∫
] Button to finish the setup.
To verify Owner ID
≥Keep pressing the [;] Button for approximately
5 seconds.
To Check Owner ID
If Owner ID has already been set, carrying out Step
1 above will display [INPUT PIN NUMBER] on the
screen. Input the Pin Number you have already
selected. If the number is not correct, the screen will
not change. If the number is correct, the contents of
the setup will be displayed. (By repeating Steps 2 to
4 above, you can change the contents.)
1 above will display [INPUT PIN NUMBER] on the
screen. Input the Pin Number you have already
selected. If the number is not correct, the screen will
not change. If the number is correct, the contents of
the setup will be displayed. (By repeating Steps 2 to
4 above, you can change the contents.)
ª Demonstration Mode
If no operation takes place for approximately
10 minutes after the AC Adaptor was connected to
the Movie Camera and the [VCR/OFF/CAMERA/
M-CARD] Switch was turned to [CAMERA] without
inserting a Cassette, the Movie Camera is
automatically set to Demonstration Mode for
introducing its functions. If any button is pressed or
operated, the Demonstration Mode is cancelled.
The Demonstration Mode can be started by setting
[DEMO MODE] on the [OTHER FUNCTIONS] Sub-
Menu of the [CAMERA FUNCTIONS] Main-Menu to
[ON] and by exiting the Menu. To terminate the
Demonstration Mode, insert a Cassette or set the
[DEMO MODE] to [OFF].
10 minutes after the AC Adaptor was connected to
the Movie Camera and the [VCR/OFF/CAMERA/
M-CARD] Switch was turned to [CAMERA] without
inserting a Cassette, the Movie Camera is
automatically set to Demonstration Mode for
introducing its functions. If any button is pressed or
operated, the Demonstration Mode is cancelled.
The Demonstration Mode can be started by setting
[DEMO MODE] on the [OTHER FUNCTIONS] Sub-
Menu of the [CAMERA FUNCTIONS] Main-Menu to
[ON] and by exiting the Menu. To terminate the
Demonstration Mode, insert a Cassette or set the
[DEMO MODE] to [OFF].
A-ENG.book 57 ページ ２００２年１月２８日 月曜日 午前１１時３２分