Toshiba D-R17DTKB Benutzerhandbuch

40

EN

Programme Delivery Control (PDC) assures that the 

TV programmes you have programmed for timer 

recording are recorded exactly from beginning to end, 

even if the actual broadcasting time differs from the 

scheduled time due to a delayed start or extension of 

the programme duration. Furthermore, if a 

programme is interrupted, the recording will also be 

interrupted automatically and resumed when the 

programme starts again.
If the PDC signal drops out because the broadcast 

signal is weak, or if a broadcasting station does not 

transmit a regular PDC signal, the timer recording is 

performed in normal mode (without PDC) even if it 

was programmed for PDC. If the starting time of the 

PDC timer recording is between 0:00 and 3:59 on a 

given day, the PDC function will operate from 20:00 

on the previous day to 4:00 on the next day. If the 

starting time of the PDC timer recording is between 

4:00 and 23:59 on a given day, the PDC function will 

operate from 0:00 on the given day to 4:00 on the 

next day. This means that if the relevant programme 

is broadcasted within this period, it is recorded 

correctly. If the timer is not programmed correctly, the 

incorrect timer setting stays in effect unless you 

cancel it. To cancel an incorrect timer setting, refer to 

“Checking, Cancelling or Correcting the Timer 

Programming Information” below. 

• This feature is only available for analogue channels.

Timer Programming list will appear.

A) To delete the timer programme:
1) Select the programme you want to delete using 

U / D], then press [ENTER/OK].

2) Select “Delete” using [

U / D], then press 

[ENTER/OK].
Confirmation window will appear.

3) Select “Yes” using [

U / D], then press 

[ENTER/OK].

B) To correct the timer programme:
1) Select the programme you want to correct 

using [

U / D], then press [ENTER/OK].

2) Select “Program Change” using [

U / D], then 

press [ENTER/OK].

3) Correct the timer programme by using 

U / D / L / P], then press [ENTER/OK].

To check the timer programming in process
Press [TIMER PROG.].

• If a timer recording is proceeding, that programme is 

highlighted in red. In such a case, you cannot select 

any other programmes.

S (STOP)] to stop the recording.

• [STOP 

S] on the remote control is not effective.

The error number appears on the Timer Programming 
list. 

The error programme will be displayed in grey 
with an asterisk and have an error number.

E1–E22, 
E37–E39: Recording error
E23–E24: Unrecordable disc
E25

: • Copy prohibited programme

• Cannot record because of the NTSC / 

PAL-60 signal is received.

E26–E28: Copy prohibited programme
E29

: Disc protected

E30

: Disc full

E31

: Already recorded 99 titles (Video 

mode)

E32

: Already recorded 99 titles (VR mode)

E33

: Already recorded 999 chapters

E34

: No space for Control Information

E35

: PCA (Power Calibration Area) full

E36

: Already finalised Video format disc

E40

: • There are some unrecorded parts due 

the overlapped timer programmes.

• Recording did not start at the start 

time.

E41

: Power failure

E42

: No disc

E43

: Already 49 titles recorded (+VR mode)

E44

: Already 254 chapters recorded 

(+VR mode)

E45

: Copy prohibited programme

E46

: It is impossible to record additionally on 

a disc recorded by other units when 
setting “Make Recording Compatible” 
to “OFF”. (+VR mode)

The error programme will be deleted once you 
check the error in the programme list, or once you 
cancel the timer-standby mode and re-enter it.

E7J70BD_EN.book  Page 40  Monday, May 7, 2007  3:31 PM