Benutzerhandbuch für Advantech HMI-640S

Inhaltsverzeichnis

• Chapter 1 General Information

  1
• Introduction

  2
• Specifications

  2
• General

  2
• Standard functions (CPC-2245N)

  2
• Ethernet interface

  4
• SVGA/Flat panel interface (CPC-2520)

  4
• Power supply

  4
• Environmental specifications

  4
• Touchscreen

  5
• LCD Specifications

  5
• I/O Arrangement

  6
• Total Solution

  7
• Dimensions

  8
• Mounting

  9
• Chapter 2 System Setup

  11
• General

  12
• Packing List

  12
• Initial Setup

  13
• Installing a CompactFlash Memory Card

  14
• Installing a CompactFlash adapter

  14
• Installing a 2.5" HDD

  15
• procedure is described as follows:

  15
• Connecting the Power Adapter

  16
• Installing a PC/104 Module

  17
• First System Boot

  19
• Power up for the first time

  19
• Assign the Device Name

  19
• Exploded Diagram

  20
• Chapter 3 Maintenance

  21
• Removing the Front/Rear Panel

  22
• LCD Display

  24
• LCD Backlight

  25
• Power Supply

  26
• I/O Adapter (CPC-2900)

  27
• (CPC-2520/CPC-2245N/CPC-2430)

  28
• Chapter 4 CPC-2245N Main Board

  29
• 4.1 Introduction

  30
• 4.2 Specifications

  31
• (40-pin FPC connector)

  32
• Mechanical and environmental

  32
• 4.3 Board layout: dimensions

  33
• 4.4 Jumpers and connectors

  34
• 4.5 Board layout: jumper/connector locations

  35
• 4.6 Safety precautions

  36
• 4.7 Setting jumpers

  37
• 4.7.1 Clear CMOS (J2)

  38
• 4.8 CompactFlash interface (CN2)

  38
• 4.9 ISA/IDE/floppy drive/parallel port (CN3)

  39
• 4.9.1 ISA bus

  42
• 4.9.2 IDE interface

  46
• 4.9.3 Floppy drive

  48
• 4.9.4 Parallel port

  49
• 4.10 VGA/LAN/serial ports/keyboard/mouse (CN4)

  50
• 4.10.1 VGA interface

  51
• 4.10.2 Ethernet configuration

  52
• 4.10.3 Keyboard and PS/2 mouse connector

  52
• Table 4-15: PS/2 mouse connector

  53
• 4.10.4 Serial ports

  53
• 4.11 Power supply connector (CN5)

  55
• 4.12 Card installation

  56
• 4.13 Card removal

  57
• 4.14 FPC cable installation

  58
• Chapter 5 CPC-2520 VGA/LCD Control Board

  59
• 5.1 Introduction

  60
• 5.2 Specifications

  61
• General

  61
• Mechanical and environmental

  61
• 5.3 Board layout: dimensions

  62
• 5.4 Jumpers and connectors

  63
• 5.5 Board layout: jumper/connector locations

  64
• 5.6 Safety precautions

  65
• 5.7 Jumper settings

  66
• 5.8 LCD panel select (SW1)

  67
• 5.9 Display connectors (CN2, CN3)

  67
• 5.10 LCD display connector (CN2)

  68
• 5.11 VGA display connector (CN3)

  69
• 5.12 FPC cable installation

  71
• Chapter 6 Networking Communication

  73
• Introduction

  74
• Networking via LAN

  74
• Networking via RS-232

  76
• Simple Networking via a Hub

  77
• Chapter A Cabling for RS-232 Port

  79
• Chapter B DIP Switch Settings

  83
• Touchscreen Specifications

  84
• Figure 4-1: Board layout: jumper/connector locations

  35
• Figure 4-2: Damping resistor

  47
• 4-1: Jumpers and connectors

  34
• 4-2: Clear CMOS (J2)

  38
• 4-3: ISA/IDE/floppy drive/parallel port connector (CN3)

  40
• 4-4: ISA bus - CN3 cross reference table (ISA pin A)

  42
• 4-5: ISA bus - CN3 cross reference table (ISA bus pin B)

  43
• 4-6: ISA bus - CN3 cross reference table (ISA bus pin C)

  44
• 4-7: ISA bus - CN3 cross reference table (IDE pin D)

  45
• 4-8: IDE hard drive connector

  46
• 4-9: Floppy drive connector

  48
• 4-10: Parallel port connector

  49
• 4-11: FPC connector (CN4)

  50
• 4-12: VGA interface

  51
• 4-13: Ethernet configuration

  52
• 4-14: PS/2 keyboard connector

  53
• 4-15: PS/2 mouse connector

  53
• 4-16: Serial port default settings

  54
• 4-17: COM1 RS-232 serial port connector

  54
• 4-18: COM2 RS-232 serial port connector

  54
• 4-19: Power supply connector (CN5)

  55
• 5-1: Jumpers and connectors

  63
• 5-2: LCD display connector (CN2)

  68
• 5-3: VGA display connector (CN3)

  69
• 5-4: VGA display connector (CN3)

  70