사용자 설명서차례Chapter 1 General Information1Introduction2Specifications2General2Standard functions (CPC-2245N)2Ethernet interface4SVGA/Flat panel interface (CPC-2520)4Power supply4Environmental specifications4Touchscreen5LCD Specifications5I/O Arrangement6Total Solution7Dimensions8Mounting9Chapter 2 System Setup11General12Packing List12Initial Setup13Installing a CompactFlash Memory Card14Installing a CompactFlash adapter14Installing a 2.5" HDD15procedure is described as follows:15Connecting the Power Adapter16Installing a PC/104 Module17First System Boot19Power up for the first time19Assign the Device Name19Exploded Diagram20Chapter 3 Maintenance21Removing the Front/Rear Panel22LCD Display24LCD Backlight25Power Supply26I/O Adapter (CPC-2900)27(CPC-2520/CPC-2245N/CPC-2430)28Chapter 4 CPC-2245N Main Board294.1 Introduction304.2 Specifications31(40-pin FPC connector)32Mechanical and environmental324.3 Board layout: dimensions334.4 Jumpers and connectors344.5 Board layout: jumper/connector locations354.6 Safety precautions364.7 Setting jumpers374.7.1 Clear CMOS (J2)384.8 CompactFlash interface (CN2)384.9 ISA/IDE/floppy drive/parallel port (CN3)394.9.1 ISA bus424.9.2 IDE interface464.9.3 Floppy drive484.9.4 Parallel port494.10 VGA/LAN/serial ports/keyboard/mouse (CN4)504.10.1 VGA interface514.10.2 Ethernet configuration524.10.3 Keyboard and PS/2 mouse connector52Table 4-15: PS/2 mouse connector534.10.4 Serial ports534.11 Power supply connector (CN5)554.12 Card installation564.13 Card removal574.14 FPC cable installation58Chapter 5 CPC-2520 VGA/LCD Control Board595.1 Introduction605.2 Specifications61General61Mechanical and environmental615.3 Board layout: dimensions625.4 Jumpers and connectors635.5 Board layout: jumper/connector locations645.6 Safety precautions655.7 Jumper settings665.8 LCD panel select (SW1)675.9 Display connectors (CN2, CN3)675.10 LCD display connector (CN2)685.11 VGA display connector (CN3)695.12 FPC cable installation71Chapter 6 Networking Communication73Introduction74Networking via LAN74Networking via RS-23276Simple Networking via a Hub77Chapter A Cabling for RS-232 Port79Chapter B DIP Switch Settings83Touchscreen Specifications84Figure 4-1: Board layout: jumper/connector locations35Figure 4-2: Damping resistor474-1: Jumpers and connectors344-2: Clear CMOS (J2)384-3: ISA/IDE/floppy drive/parallel port connector (CN3)404-4: ISA bus - CN3 cross reference table (ISA pin A)424-5: ISA bus - CN3 cross reference table (ISA bus pin B)434-6: ISA bus - CN3 cross reference table (ISA bus pin C)444-7: ISA bus - CN3 cross reference table (IDE pin D)454-8: IDE hard drive connector464-9: Floppy drive connector484-10: Parallel port connector494-11: FPC connector (CN4)504-12: VGA interface514-13: Ethernet configuration524-14: PS/2 keyboard connector534-15: PS/2 mouse connector534-16: Serial port default settings544-17: COM1 RS-232 serial port connector544-18: COM2 RS-232 serial port connector544-19: Power supply connector (CN5)555-1: Jumpers and connectors635-2: LCD display connector (CN2)685-3: VGA display connector (CN3)695-4: VGA display connector (CN3)70크기: 1.16메가바이트페이지: 94Language: English매뉴얼 열기