Benutzerhandbuch für Alamo 60C

Inhaltsverzeichnis

• 60C

  1
• OPERATOR’S MANUAL

  1
  • ALAMO (SMC)

    1
• TO THE OWNER/OPERATOR/DEALER

  2
  • BACKHOE

    1
  • General Safety Instructions and Practices

    6
  • Connecting and Disconnecting Safety Instructions and Practices

    9
  • Equipment Operation Safety Instructions and Practices

    10
  • Transporting Safety Instructions and Practices

    15
  • Storage Safety Instructions and Practices

    17
  • Maintenance Safety Instructions and Practices

    17
  • Concluding Safety Instructions and Practices

    18
    • Decal Location

      19
      • 1. 44897 2 DANGER Crushing Hazard

        20
      • 2. 54687 1 LOGO 60C (Small)

        20
      • 3. 54686 2 LOGO 60C (Big)

        20
      • 4. NFS 1 SER PLT Serial Plate

        20
      • 5. 38850-2 2 ________ Rivet, Metal Piercing (Not Shown)

        20
      • 6. 44909 1 OPERATION Swing Lock

        20
      • 7. 44908 1 OPERATION Boom Lock

        20
      • 8. 44901 1 OPERATION Right Side Stabilizer Position

        20
      • 9. 44900 1 OPERATION Left Side Stabilizer Position

        20
      • 10. 44899 1 OPERATION Dipperstick & Bucket Operation

        20
      • 11. 44898 1 OPERATION Boom Operation

        20
      • 12. 48280 1 INFORMATION Universal One Call

        20
      • 13. 44907 1 WARNING To Prevent Instability

        20
      • 14. 45970 1 WARNING To Prevent Bodily Injury

        20
      • 15. 44896 1 WARNING To Prevent Bodily Injury

        20
      • 16. 44895 2 DANGER Crushing Hazard

        20
      • 17. 52154 3 LOGO Alamo SMC

        20
  • Decal Description

    21
  • Federal Laws and Regulations

    23
    • SAFETY SECTION

      5
    • SPECIFICATIONS

      27
      • INTRODUCTION SECTION

        25
      • ASSEMBLY SECTION

        29
  • MOUNTING BACKHOE TO TRACTOR

    30
    • 1. Back tractor close enough to backhoe to connect hose kit or pump to tractor.

      30
    • 2. Using backhoe hydraulics, lower stabilizers until backhoe can be connected to 3-point hitch. Bottom of backhoe boom pivot should be 8 to 12 inches off ground when attaching to tractor lower 3-point arms.

      30
    • 3. Connect lower 3-point hitch members to backhoe and secure using linch pins from 3-point hitch.

      30
    • 4. Connect link assembly to upper connecting point on 3-point hitch using clevis pin and linch pin from 3-point hitch.

      30
    • 5. Adjust link assembly length if necessary for backhoe mainframe to rest in vertical position.

      30
    • 6. Check for proper operator head clearance with ROPS and cab (Figure 4).

      30
    • 7. Tighten all hardware in upper link assembly to torque specifications in backhoe manual.

      30
  • PARTS LIST

    32
    • Mainframe Assembly

      32
      • Mainframe Assembly Parts List

        33
        • 1. 54712 1 CONSOLE W/ DECALS

          33
        • 2. 53717 1 COVER PLATE

          33
        • 3. 54457 2 STABILIZER

          33
        • 4. 53707 2 PAD, STABILIZER

          33
        • 5. 47272 2 CYLINDER STABILIZER

          33
        • 6. 44831 2 BUMPER, RUBBER

          33
        • 7. 54463 2 LOCK STABILIZER

          33
        • 8. 41838-100 2 SCREW, CAP 3/4-10 X 6.5 GR5

          33
        • 9. 6077-9 2 NUT, ELASTIC STOP 3/4-10

          33
        • 10. 41903-13 2 PIN, COTTER

          33
        • 11. 41902-3 2 PIN, CLEVIS

          33
        • 12. 31332-7 2 PIN, 1.00” X 4.12

          33
        • 13. 41838-28 2 SCREW, CAP 5/16-18 X 2 GR5

          33
        • 14. 46632-5 2 PIN, 1.00 X 5.25

          33
        • 15. 42502-8 8 WASHER, FLAT 3/8

          33
        • 16. 47046 2 BOLT, SHOLDER 3/8-16 X 1.00 GR5

          33
        • 17. 46303-6 6 TUBE, SPACER

          33
        • 18. 41838-17 6 SCREW, CAP 3/8-16 X 2.00 GR5

          33
        • 19. 41840-3 8 NUT, LOCK 3/8-16

          33
        • 20. 42502-7 4 WASHER, FLAT 5/16

          33
        • 21. 41840-2 4 NUT, LOCK 5/16-18

          33
        • 22. 6067-1 2 NUT SPEED

          33
        • 23. 41837-2 2 WASHER, LOCK 5/16

          33
        • 24. 41838-26 4 SCREW, CAP 5/16-18 X 0.75 GR5

          33
        • 25. 6075-4 6 FITTING, GREASE 1/4-28

          33
        • 26. 54464 1 COVER, SEAT BRACKET

          33
        • 27. 25820-6 1 ANTI SKID SURFACE

          33
        • 28. 41901-2 1 PIN, COTTER

          33
        • 29. 45970 1 DECAL, WARNING

          33
        • 30. 44907 1 DECAL, WARNING

          33
        • 31. 44895 2 DECAL, DANGER

          33
        • 32. 44896 1 DECAL, WARNING

          33
        • 33. 44897 2 DECAL, DANGER

          33
        • 34. 44898 1 DECAL, OPERATION

          33
        • 35. 44899 1 DECAL, OPERATION

          33
        • 36. 44900 1 DECAL, OPERATION

          33
        • 37. 44901 1 DECAL, OPERATION

          33
        • 38. 44909 1 DECAL, SWING LOCK

          33
        • 39. 48280 1 DECAL, UNIVERSAL ONE CALL

          33
        • 40. 52454 1 DECAL, ALAMO SMC

          33
        • 41. 54687 1 DECAL, 60C SMALL

          33
        • 42. 54427 1 MAINFRAME

          33
        • 43. 54884 2 BUMPER, 2” DIAMETER

          33
        • 44. 41838-95 2 SCREW, CAP 1/2-13 X 0.75 GR5

          33
        • 45. 41837-5 2 WASHER, LOCK 1/2

          33
      • Mainframe Assembly w/o Seat

        34
      • Mainframe Assembly w/o Seat Parts List

        35
        • 1. 54712 1 CONSOLE W/ DECALS

          35
        • 2. 53717 1 COVER PLATE

          35
        • 3. 54457 2 STABILIZER

          35
        • 4. 53707 2 PAD, STABILIZER

          35
        • 5. 47272 2 CYLINDER STABILIZER

          35
        • 6. 44831 2 BUMPER, RUBBER

          35
        • 7. 54463 2 LOCK STABILIZER

          35
        • 8. 41838-100 2 SCREW, CAP 3/4-10 X 6.5 GR5

          35
        • 9. 6077-9 2 NUT, ELASTIC STOP 3/4-10

          35
        • 10. 41903-13 2 PIN, COTTER

          35
        • 11. 41902-3 2 PIN, CLEVIS

          35
        • 12. 31332-7 2 PIN, 1.00” X 4.12

          35
        • 13. 41838-28 2 SCREW, CAP 5/16-18 X 2 GR5

          35
        • 14. 46632-5 2 PIN, 1.00 X 5.25

          35
        • 15. 42502-8 8 WASHER, FLAT 3/8

          35
        • 16. 47046 2 BOLT, SHOLDER 3/8-16 X 1.00 GR5

          35
        • 17. 46303-6 6 TUBE, SPACER

          35
        • 18. 41838-17 6 SCREW, CAP 3/8-16 X 2.00 GR5

          35
        • 19. 41840-3 8 NUT, LOCK 3/8-16

          35
        • 20. 42502-7 4 WASHER, FLAT 5/16

          35
        • 21. 41840-2 4 NUT, LOCK 5/16-18

          35
        • 22. 6067-1 2 NUT SPEED

          35
        • 23. 41837-2 2 WASHER, LOCK 5/16

          35
        • 24. 41838-26 4 SCREW, CAP 5/16-18 X 0.75 GR5

          35
        • 25. 6075-4 6 FITTING, GREASE 1/4-28

          35
        • 26. 54533 1 COVER, FLOOR PLATE

          35
        • 27. 41839-14 2 BOLT, CARRIAGE, 5/16-18 X 0.75 GR5

          35
        • 28. 25820-4 1 ANTI SKID SURFACE, 2 X 9

          35
        • 29. 25820-6 1 ANTI SKID SURFACE, 4 X 6

          35
        • 30. 45970 1 DECAL, WARNING

          35
        • 31. 44907 1 DECAL, WARNING

          35
        • 32. 44895 2 DECAL, DANGER

          35
        • 33. 44896 1 DECAL, WARNING

          35
        • 34. 44897 2 DECAL, DANGER

          35
        • 35. 44898 1 DECAL, OPERATION

          35
        • 36. 44899 1 DECAL, OPERATION

          35
        • 37. 44900 1 DECAL, OPERATION

          35
        • 38. 44901 1 DECAL, OPERATION

          35
        • 39. 44909 1 DECAL, SWING LOCK

          35
        • 40. 48280 1 DECAL, UNIVERSAL ONE CALL

          35
        • 41. 52454 1 DECAL, ALAMO SMC

          35
        • 42. 54687 1 DECAL, 60C SMALL

          35
        • 43. 54427 1 MAINFRAME

          35
        • 44. 54884 2 BUMPER, 2” DIAMETER

          35
        • 45. 41838-95 2 SCREW, CAP 1/2-13 X 0.75 GR

          35
        • 46. 41837-5 2 WASHER, LOCK 1/2

          35
      • Swing Frame Assembly

        36
      • Swing Frame Assembly

        37
        • 1. 54496 1 CYLINDER, SWING

          37
        • 2. 54448 1 SWING FRAME

          37
        • 3. 41838-28 3 SCREW, CAP 5/16-18 X 2 GR5

          37
        • 4. 41840-3 2 NUT, LOCK 3/8-16

          37
        • 5. 41840-2 3 NUT, LOCK 5/16-18

          37
        • 6. 6075-4 2 FITTING, GREASE 1/4-28

          37
        • 7. 6075-2 2 FITTING, GREASE 1/8 SELF TAP

          37
        • 8. 54445 2 PIN, SWING FRAME 1-1/2

          37
        • 9. 46632-5 1 PIN, 1 X 5.25

          37
        • 10. 54713 1 PIN, HT 1 X 5.25

          37
        • 11. 41838-9 2 SCREW, CAP 3/8-16 X 1.25 GR5

          37
        • 12. 44873 3 WASHER, THRUST

          37
        • 13. 41902-16 1 PIN, CLEVIS

          37
        • 14. 41901-4 1 HAIR PIN, COTTER

          37
        • 15. 42577-5 2 BUSHING, MACHINERY

          37
        • 16. 54476 1 LOCK, BOOM

          37
        • 17. 41867-1 1 PIN, 1 X 5.69

          37
        • 18. 45252-1 2 BUSHING, SLEEVE

          37
        • 19. 42502-8 2 WASHER, FLAT 3/8

          37
        • 20. 45252-3 2 BUSHING, 1 I.D. X 1.25 O.D. X 1.00

          37
        • 21. 48948-3 2 NUT, JAM 3/8-16

          37
      • Boom Assembly

        38
      • Boom Assembly Parts List

        39
        • 1. 54465 1 BOOM

          39
        • 2. 54489 1 CYLINDER, BOOM

          39
        • 3. 54503 1 CYLINDER, DIPPERSTICK

          39
        • 4. 47318 2 PIN, 1-1/4 X 6.62

          39
        • 5. 41838-54 2 SCREW, CAP 3/8-16 X 2.50 GR5

          39
        • 6. 41840-3 2 NUT, LOCK3/8-16

          39
        • 7. 41838-28 1 SCREW, CAP 5/16-18 X 2 GR5

          39
        • 8. 41840-2 1 NUT, LOCK 5/16-18

          39
        • 9. 6075-4 3 FITTING, GREASE 1/4-28

          39
        • 10. 6075-2 2 FITTING, GREASE 1/8 SELF TAP

          39
        • 11. 46632-5 1 PIN, 1 X 5.25

          39
        • 12. 6077-8 3 NUT, ELASTIC STOP 3/8

          39
        • 13. 6079-9 1 GROMMET, RUBBER

          39
        • 14. 53297 1 CLAMP

          39
        • 15. 13722 2 CLAMP

          39
        • 16. 41838-23 1 SCREW, CAP 3/8-16 X 1.50 GR5

          39
        • 17. 44908 1 DECAL, BOOM LOCK

          39
        • 18. 52154 2 DECAL, ALAMO SMC

          39
        • 19. 54686 2 DECAL, 60C BIG

          39
      • Dipperstick and Bucket Assembly

        40
      • Dipperstick and Bucket Assembly Parts List

        41
      • Valve Assembly

        42
      • Valve Assembly Parts List

        43
      • Hydraulic Schematic

        44
    • Hydraulic Schematic Parts List

      45
      • Seat Assembly

        46
      • Seat Assembly Parts List

        47
      • Cylinder Assembly - Swing

        48
    • Cylinder Assembly - Swing Parts List

      48
      • Cylinder Assembly - Bucket

        49
    • Cylinder Assembly - Bucket Parts List

      49
      • Cylinder Assembly - Boom

        50
    • Cylinder Assembly - Boom Parts List

      50
      • Cylinder Assembly - Dipper

        51
    • Cylinder Assembly - Dipper Parts List

      51
      • Cylinder Assembly - Stabilizer

        52
    • Cylinder Assembly - Stabilizer Parts List

      52
      • OPERATION SECTION

        53
  • PRE-OPERATION CHECKLIST

    54
    • 1. All safety shields must be in place.

      54
    • 2. Safety and operation decals must be in place, undamaged and clean.

      54
    • 3. Hydraulic hookup must be correct and all connections tight.

      54
    • 4. All bolts and pins which attach backhoe to tractor must be in place. Check tightness of bolts and check that all pins are retained.

      54
    • 5. Tractor must be in proper operating condition.

      54
    • 6. Lubricate backhoe, see MAINTENANCE SECTION.

      54
    • 7. Controls must operate properly. See OPERATION SECTION.

      54
    • 8. Cycle all cylinders slowly to purge air from hydraulic system.

      54
    • 9. Hydraulic system oil level must be correct. Reservoir level should be 1” from top of tank.

      54
  • OPERATING DIRECTIONS

    54
  • ENGINE SPEED

    54
  • CONTROLS

    54
  • BOOM/SWING

    54
  • CROWD/BUCKET

    54
  • LEFT HAND STABILIZER

    55
  • RIGHT HAND STABILIZER

    55
  • OPERATING BACKHOE

    55
    • FILLING BUCKET

      56
  • DUMPING BUCKET

    56
  • TRENCHING BETWEEN A BUILDING & OPEN EXCAVATORS

    56
    • Position the unit so the backhoe swing post is over the center line of the trench connection. Dig with the backhoe at extreme swing positions, and in as close to the stabilizers as possible. Pile the soil on the opposite side of the trenches.

      57
  • SIDE SLOPE EXCAVATING OR TRENCHING

    57
  • MISCELLANEOUS

    58
  • FINISHING STRAIGHT WALLS

    58
  • BACKFILLING

    58
  • SEAT ADJUSTMENT

    58
    • MOUNTING AND DISMOUNTING BUCKETS

      59
  • PLACING THE STABILIZERS

    59
  • SWING LOCK

    59
  • BOOM LOCK

    59
    • 1. Completely raise boom and lower dipperstick.

      59
    • 2. Secure boom using boom lock bracket.

      59
  • STABILIZER LOCK

    59
    • 1. Completely raise stabilizers.

      59
    • 2. Secure each stabilizer using stabilizer lock brackets.

      59
    • TRANSPORTING THE BACKHOE

      60
  • REMOVAL FROM TRACTOR - STORAGE

    60
    • 1. Put stabilizers down and lift backhoe slightly. Rotate boom straight back.

      60
    • 2. Install swing lock pin.

      60
    • 3. Complete raise boom and lower dipperstick. Curl bucket until bottom of bucket is level with ground. Lower boom until bucket rests firmly on ground.

      60
    • 4. Remove pins which secure backhoe to tractor.

      60
    • 5. Lower front of subframe to rest on ground.

      60
    • 6. Slowly drive forward until tractor clears backhoe. Engage tractor brakes.

      60
    • 7. Lower backhoe by raising stabilizers and boom until backhoe or subframe rests on suitable blocking. Leave stabilizers touching ground.

      60
    • 8. Shut off tractor. Work handles back and forth to relieve hydraulic pressure. Disconnect hydraulic lines or pump from backhoe.

      60
    • 9. For long term storage, coat all exposed cylinder rods with grease.

      60
    • 10. Lubricate all grease fittings, stabilizer pivot pins and complete handle linkage.

      60
    • MAINTENANCE SECTION

      61
      • 1 O-RING 1

        69
      • 2 O-RING 1

        69
      • 3 VALVE BODY/RELIEF 1

        69
      • 4 PISTON 1

        69
      • 5 SPRING 1

        69
      • 6 O-RING 1

        69
      • 7 REGISTER 1

        69
      • 8 NUT, M16-1.5 1

        69
      • 9 DEFLECTOR 1

        69
      • 10 O-RING 5

        69
      • 11 CENTERING RING 5

        69
      • 12 SPRING 5

        69
      • 13 SPACER 10

        69
      • 14 SCREW 5

        69
      • 15 CAP 20

        69
      • 16 SCREW 20

        69
      • 17 SCREW 4

        69
      • 18 CIRCLIP 1

        69
      • 19 WASHER 1

        69
      • 20 BUSHING 1

        69
      • 21 SPRING 1

        69
      • 22 BALL HOLDER 1

        69
      • 23 STEEL BALL D.5 3

        69
      • 24 STEEL BALL D.7 1

        69
      • 25 CAP 1

        69
      • 26 WASHER 1

        69
      • 27 SPACER 1

        69
      • 28 SPRING 1

        69
      • 29 SPACER 1

        69
      • 30 CENTERING RING 1

        69
      • 31 O-RING 15.10 X 2.70 X 1.5 1

        69
      • 32 PLUG 4

        69
      • 33 COPPER GASKET 14 X 20 X 15 4

        69
      • 34 REGISTER 4

        69
      • 35 SPRING 4

        69
      • 36 PISTON 4

        69
      • 37 VALVE BODY/RELIEF 4

        69
      • 38 O-RING 17.17 X 1.78 4

        69
      • 39 O-RING 4

        69
      • 40 PLUG 1

        69
      • 41 O-RING 17.17 X 1.78 1

        69
      • 42 O-RING 1

        69
      • 43 PLUG 6

        69
      • 44 SPRING 6

        69
      • 45 O-RING 11.11 X 1.78 6

        69
      • 46 BODY 6

        69
      • 47 PLUG 1

        69
      • 48 LEVER 2

        69
      • 49 RUBBER BELLOWS 2

        69
      • 50 HOUSING/LEVER 2

        69
      • 51 O-RING 15.10 X 2.70 2

        69
      • 52 CENTERING RING 2

        69
      • 53 LEVER PIN 2

        69
      • 54 SCREW 8

        69
      • 55 O-RING 15.10 X 2.70 4

        69
      • 56 NUT 3

        69
      • 57 PLATE/JOYSTICK 1

        69
      • 58 SCREW 8

        69
      • 59 ASSEMBLY 2

        69
      • 60 ASSEMBLY 2

        69
      • 61 PIN 2

        69
      • 62 FLANGE 1

        69
      • 63 SCREW 6

        69
      • 64 NUT, M7 4

        69
      • 65 O-RING GASKET 2

        69
      • 66 RUBBER BELLOWS 2

        69
      • 67 SCREW 4

        69
      • 68 ARICULATION 2

        69
      • 69 NUT, M6 2

        69
      • 70 FLANGE 1

        69
      • 71 CENTERING RING 1

        69
      • 72 O-RING 15.60 X 1.78 1

        69
      • 73 PLATE/JOYSTICK 1

        69
      • 74 VALVE BLOCK 1

        69
      • 75 PLUG 1

        69
  • CYLINDER SERVICE

    62
    • CYLINDER DISASSEMBLY

      62
      • 1. Hold cylinder tube (13) stationary and pull wire ring (14) out through slot. Rotate head (6) to ease disassembly.

        62
      • 2. Pull shaft (1), with all assembled parts, out of cylinder tube.

        62
      • 3. Remove lock nut (12) from end of shaft and slide piston (8) and cylinder head (6) off shaft.

        62
      • 4. Remove piston wear ring (11), piston seal (10) and o- ring (9) from outside grooves on piston (Swing cylinders have additional steel ring between piston and nut).

        62
      • 5. Remove wiper seal (2), rod seal (3) and wear ring (7) from inside of cylinder head and o-ring (5) with backup washer (4) from groove on outside of head.

        62
      • 6. Clean all parts including cylinder tube, in a suitable cleaning solvent, then use air pressure to blow any dirt or excess solvent from all parts.

        62
      • 7. Examine all parts for wear or damage and replace, if necessary.

        62
    • CYLINDER ASSEMBLY

      62
      • 1. Place rod seal (3) into groove inside cylinder head.

        62
      • 2. Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head. Install wear ring (7) inside other end of head.

        62
      • 3. Place o-ring (5) with backup washer (4) in groove on outside of head. Backup washer must be on rod side.

        62
      • 4. Remove sharp edges on outer edge of threaded end of shaft (1). Lubricate wiper seal (2) and rod seal (3) in head and carefully slide head onto shaft.

        62
      • 5. Place o-ring (9), piston seal (10) and piston wear ring (11) in grooves on outside of piston.

        62
      • 6. Slide piston onto threaded end of shaft and install lock nut (12). Swing, bucket and stabilizers cylinders; tighten lock nut (12) to 300 ft./lbs. Lift and dipperstick cylinders; tighten lock nut (12) to 375 ft./lbs. on lift cylinders.

        62
      • 7. Lubricate piston wear ring (11) and piston seal (10) on piston, o-ring (5) and backup washer (4) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube.

        62
      • 8. Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.

        62
  • BEGINNING OF SEASON

    63
  • HYDRAULIC HOSES

    63
  • HYDRAULIC SYSTEM RESERVOIR

    63
  • BUCKET TOOTH POINTS

    64
  • TIGHTENING NUTS AND BOLTS

    64
  • LUBRICATION

    64
  • LUBRICATION CHART

    64
  • HYDRAULIC TROUBLESHOOTING

    65
  • VALVE SERVICE

    67
    • MAIN RELIEF REPLACEMENT

      67
      • 1. Use a socket to remove main relief from valve housing.

        67
      • 2. Inspect new relief to ensure seal is properly installed, and apply grease around the relief.

        67
      • 3. Ensure that pressure setting stamped on new relief matches the setting of old relief.

        67
      • 4. Install o-rings on relief.

        67
      • 5. Insert relief and torque to 60 ft./lbs.

        67
    • SPOOL SEAL INSTALLATION

      67
      • 1. Remove the mechanical joystick kit from the top of the valve and the return kit from the bottom.

        67
      • 2. Remove the old o-rings and leave spool in housing, making sure spool is in center position.

        67
      • 3. Lightly oil one seal and insert it in top of valve. Slide the seal into position in the groove in the valve body, making sure that it does not fall into the spool groove.

        67
      • 4. Lightly oil a second o-ring and insert in bottom of valve. Slide the seal into position in the groove in the valve body making sure it does not fall into the spool groove. Do not push on the spool as it may cause the first seal to come out of the ...

        67
      • 5. Reinstall the mechanical joystick kit on the top of the valve and return kit on the bottom.

        67
    • TORQUE SETTINGS

      67
      • 1. Main Relief Body: 60 ft./lbs.

        67
      • 2. Load Check Valve: 15 ft./lbs.

        67
      • 3. Screws: 4 ft./lbs.

        67
  • PARTS LIST

    69
  • PROPER TORQUE FOR FASTENERS

    70
• ALAMO SMC

  72
  • LIMITED WARRANTY

    72
  • 1. LIMITED WARRANTIES

    72
  • 1.01. Alamo SMC warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that ...

    72
  • 1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.

    72
  • 1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...

    72
  • 1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.

    72
  • 2. REMEDIES AND PROCEDURES.

    72
  • 2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.

    72
  • 2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based

    72
  • 2.03. Purchaser is responsible for returning the goods in question to the Dealer.

    72
  • 2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:

    72
    • (a) Repair or replace the defective goods or part(s) or

      72
    • (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.

      72
  • 2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...

    72
  • 3. LIMITATION OF LIABILITY.

    72
  • 3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

    72
  • 3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.

    72
  • 3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...

    72
  • 3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.

    72
  • 4. MISCELLANEOUS.

    72
  • 4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.

    72
  • 4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.

    72
  • 4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.

    72
  • 4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

    72
    • ALAMO SMC

      72
• TO THE OWNER/OPERATOR/DEALER

  73