Manuel D’UtilisationTable des matières60C1OPERATOR’S MANUAL1ALAMO (SMC)1TO THE OWNER/OPERATOR/DEALER2BACKHOE1General Safety Instructions and Practices6Connecting and Disconnecting Safety Instructions and Practices9Equipment Operation Safety Instructions and Practices10Transporting Safety Instructions and Practices15Storage Safety Instructions and Practices17Maintenance Safety Instructions and Practices17Concluding Safety Instructions and Practices18Decal Location191. 44897 2 DANGER Crushing Hazard202. 54687 1 LOGO 60C (Small)203. 54686 2 LOGO 60C (Big)204. NFS 1 SER PLT Serial Plate205. 38850-2 2 ________ Rivet, Metal Piercing (Not Shown)206. 44909 1 OPERATION Swing Lock207. 44908 1 OPERATION Boom Lock208. 44901 1 OPERATION Right Side Stabilizer Position209. 44900 1 OPERATION Left Side Stabilizer Position2010. 44899 1 OPERATION Dipperstick & Bucket Operation2011. 44898 1 OPERATION Boom Operation2012. 48280 1 INFORMATION Universal One Call2013. 44907 1 WARNING To Prevent Instability2014. 45970 1 WARNING To Prevent Bodily Injury2015. 44896 1 WARNING To Prevent Bodily Injury2016. 44895 2 DANGER Crushing Hazard2017. 52154 3 LOGO Alamo SMC20Decal Description21Federal Laws and Regulations23SAFETY SECTION5SPECIFICATIONS27INTRODUCTION SECTION25ASSEMBLY SECTION29MOUNTING BACKHOE TO TRACTOR301. Back tractor close enough to backhoe to connect hose kit or pump to tractor.302. Using backhoe hydraulics, lower stabilizers until backhoe can be connected to 3-point hitch. Bottom of backhoe boom pivot should be 8 to 12 inches off ground when attaching to tractor lower 3-point arms.303. Connect lower 3-point hitch members to backhoe and secure using linch pins from 3-point hitch.304. Connect link assembly to upper connecting point on 3-point hitch using clevis pin and linch pin from 3-point hitch.305. Adjust link assembly length if necessary for backhoe mainframe to rest in vertical position.306. Check for proper operator head clearance with ROPS and cab (Figure 4).307. Tighten all hardware in upper link assembly to torque specifications in backhoe manual.30PARTS LIST32Mainframe Assembly32Mainframe Assembly Parts List331. 54712 1 CONSOLE W/ DECALS332. 53717 1 COVER PLATE333. 54457 2 STABILIZER334. 53707 2 PAD, STABILIZER335. 47272 2 CYLINDER STABILIZER336. 44831 2 BUMPER, RUBBER337. 54463 2 LOCK STABILIZER338. 41838-100 2 SCREW, CAP 3/4-10 X 6.5 GR5339. 6077-9 2 NUT, ELASTIC STOP 3/4-103310. 41903-13 2 PIN, COTTER3311. 41902-3 2 PIN, CLEVIS3312. 31332-7 2 PIN, 1.00” X 4.123313. 41838-28 2 SCREW, CAP 5/16-18 X 2 GR53314. 46632-5 2 PIN, 1.00 X 5.253315. 42502-8 8 WASHER, FLAT 3/83316. 47046 2 BOLT, SHOLDER 3/8-16 X 1.00 GR53317. 46303-6 6 TUBE, SPACER3318. 41838-17 6 SCREW, CAP 3/8-16 X 2.00 GR53319. 41840-3 8 NUT, LOCK 3/8-163320. 42502-7 4 WASHER, FLAT 5/163321. 41840-2 4 NUT, LOCK 5/16-183322. 6067-1 2 NUT SPEED3323. 41837-2 2 WASHER, LOCK 5/163324. 41838-26 4 SCREW, CAP 5/16-18 X 0.75 GR53325. 6075-4 6 FITTING, GREASE 1/4-283326. 54464 1 COVER, SEAT BRACKET3327. 25820-6 1 ANTI SKID SURFACE3328. 41901-2 1 PIN, COTTER3329. 45970 1 DECAL, WARNING3330. 44907 1 DECAL, WARNING3331. 44895 2 DECAL, DANGER3332. 44896 1 DECAL, WARNING3333. 44897 2 DECAL, DANGER3334. 44898 1 DECAL, OPERATION3335. 44899 1 DECAL, OPERATION3336. 44900 1 DECAL, OPERATION3337. 44901 1 DECAL, OPERATION3338. 44909 1 DECAL, SWING LOCK3339. 48280 1 DECAL, UNIVERSAL ONE CALL3340. 52454 1 DECAL, ALAMO SMC3341. 54687 1 DECAL, 60C SMALL3342. 54427 1 MAINFRAME3343. 54884 2 BUMPER, 2” DIAMETER3344. 41838-95 2 SCREW, CAP 1/2-13 X 0.75 GR53345. 41837-5 2 WASHER, LOCK 1/233Mainframe Assembly w/o Seat34Mainframe Assembly w/o Seat Parts List351. 54712 1 CONSOLE W/ DECALS352. 53717 1 COVER PLATE353. 54457 2 STABILIZER354. 53707 2 PAD, STABILIZER355. 47272 2 CYLINDER STABILIZER356. 44831 2 BUMPER, RUBBER357. 54463 2 LOCK STABILIZER358. 41838-100 2 SCREW, CAP 3/4-10 X 6.5 GR5359. 6077-9 2 NUT, ELASTIC STOP 3/4-103510. 41903-13 2 PIN, COTTER3511. 41902-3 2 PIN, CLEVIS3512. 31332-7 2 PIN, 1.00” X 4.123513. 41838-28 2 SCREW, CAP 5/16-18 X 2 GR53514. 46632-5 2 PIN, 1.00 X 5.253515. 42502-8 8 WASHER, FLAT 3/83516. 47046 2 BOLT, SHOLDER 3/8-16 X 1.00 GR53517. 46303-6 6 TUBE, SPACER3518. 41838-17 6 SCREW, CAP 3/8-16 X 2.00 GR53519. 41840-3 8 NUT, LOCK 3/8-163520. 42502-7 4 WASHER, FLAT 5/163521. 41840-2 4 NUT, LOCK 5/16-183522. 6067-1 2 NUT SPEED3523. 41837-2 2 WASHER, LOCK 5/163524. 41838-26 4 SCREW, CAP 5/16-18 X 0.75 GR53525. 6075-4 6 FITTING, GREASE 1/4-283526. 54533 1 COVER, FLOOR PLATE3527. 41839-14 2 BOLT, CARRIAGE, 5/16-18 X 0.75 GR53528. 25820-4 1 ANTI SKID SURFACE, 2 X 93529. 25820-6 1 ANTI SKID SURFACE, 4 X 63530. 45970 1 DECAL, WARNING3531. 44907 1 DECAL, WARNING3532. 44895 2 DECAL, DANGER3533. 44896 1 DECAL, WARNING3534. 44897 2 DECAL, DANGER3535. 44898 1 DECAL, OPERATION3536. 44899 1 DECAL, OPERATION3537. 44900 1 DECAL, OPERATION3538. 44901 1 DECAL, OPERATION3539. 44909 1 DECAL, SWING LOCK3540. 48280 1 DECAL, UNIVERSAL ONE CALL3541. 52454 1 DECAL, ALAMO SMC3542. 54687 1 DECAL, 60C SMALL3543. 54427 1 MAINFRAME3544. 54884 2 BUMPER, 2” DIAMETER3545. 41838-95 2 SCREW, CAP 1/2-13 X 0.75 GR3546. 41837-5 2 WASHER, LOCK 1/235Swing Frame Assembly36Swing Frame Assembly371. 54496 1 CYLINDER, SWING372. 54448 1 SWING FRAME373. 41838-28 3 SCREW, CAP 5/16-18 X 2 GR5374. 41840-3 2 NUT, LOCK 3/8-16375. 41840-2 3 NUT, LOCK 5/16-18376. 6075-4 2 FITTING, GREASE 1/4-28377. 6075-2 2 FITTING, GREASE 1/8 SELF TAP378. 54445 2 PIN, SWING FRAME 1-1/2379. 46632-5 1 PIN, 1 X 5.253710. 54713 1 PIN, HT 1 X 5.253711. 41838-9 2 SCREW, CAP 3/8-16 X 1.25 GR53712. 44873 3 WASHER, THRUST3713. 41902-16 1 PIN, CLEVIS3714. 41901-4 1 HAIR PIN, COTTER3715. 42577-5 2 BUSHING, MACHINERY3716. 54476 1 LOCK, BOOM3717. 41867-1 1 PIN, 1 X 5.693718. 45252-1 2 BUSHING, SLEEVE3719. 42502-8 2 WASHER, FLAT 3/83720. 45252-3 2 BUSHING, 1 I.D. X 1.25 O.D. X 1.003721. 48948-3 2 NUT, JAM 3/8-1637Boom Assembly38Boom Assembly Parts List391. 54465 1 BOOM392. 54489 1 CYLINDER, BOOM393. 54503 1 CYLINDER, DIPPERSTICK394. 47318 2 PIN, 1-1/4 X 6.62395. 41838-54 2 SCREW, CAP 3/8-16 X 2.50 GR5396. 41840-3 2 NUT, LOCK3/8-16397. 41838-28 1 SCREW, CAP 5/16-18 X 2 GR5398. 41840-2 1 NUT, LOCK 5/16-18399. 6075-4 3 FITTING, GREASE 1/4-283910. 6075-2 2 FITTING, GREASE 1/8 SELF TAP3911. 46632-5 1 PIN, 1 X 5.253912. 6077-8 3 NUT, ELASTIC STOP 3/83913. 6079-9 1 GROMMET, RUBBER3914. 53297 1 CLAMP3915. 13722 2 CLAMP3916. 41838-23 1 SCREW, CAP 3/8-16 X 1.50 GR53917. 44908 1 DECAL, BOOM LOCK3918. 52154 2 DECAL, ALAMO SMC3919. 54686 2 DECAL, 60C BIG39Dipperstick and Bucket Assembly40Dipperstick and Bucket Assembly Parts List41Valve Assembly42Valve Assembly Parts List43Hydraulic Schematic44Hydraulic Schematic Parts List45Seat Assembly46Seat Assembly Parts List47Cylinder Assembly - Swing48Cylinder Assembly - Swing Parts List48Cylinder Assembly - Bucket49Cylinder Assembly - Bucket Parts List49Cylinder Assembly - Boom50Cylinder Assembly - Boom Parts List50Cylinder Assembly - Dipper51Cylinder Assembly - Dipper Parts List51Cylinder Assembly - Stabilizer52Cylinder Assembly - Stabilizer Parts List52OPERATION SECTION53PRE-OPERATION CHECKLIST541. All safety shields must be in place.542. Safety and operation decals must be in place, undamaged and clean.543. Hydraulic hookup must be correct and all connections tight.544. All bolts and pins which attach backhoe to tractor must be in place. Check tightness of bolts and check that all pins are retained.545. Tractor must be in proper operating condition.546. Lubricate backhoe, see MAINTENANCE SECTION.547. Controls must operate properly. See OPERATION SECTION.548. Cycle all cylinders slowly to purge air from hydraulic system.549. Hydraulic system oil level must be correct. Reservoir level should be 1” from top of tank.54OPERATING DIRECTIONS54ENGINE SPEED54CONTROLS54BOOM/SWING54CROWD/BUCKET54LEFT HAND STABILIZER55RIGHT HAND STABILIZER55OPERATING BACKHOE55FILLING BUCKET56DUMPING BUCKET56TRENCHING BETWEEN A BUILDING & OPEN EXCAVATORS56Position the unit so the backhoe swing post is over the center line of the trench connection. Dig with the backhoe at extreme swing positions, and in as close to the stabilizers as possible. Pile the soil on the opposite side of the trenches.57SIDE SLOPE EXCAVATING OR TRENCHING57MISCELLANEOUS58FINISHING STRAIGHT WALLS58BACKFILLING58SEAT ADJUSTMENT58MOUNTING AND DISMOUNTING BUCKETS59PLACING THE STABILIZERS59SWING LOCK59BOOM LOCK591. Completely raise boom and lower dipperstick.592. Secure boom using boom lock bracket.59STABILIZER LOCK591. Completely raise stabilizers.592. Secure each stabilizer using stabilizer lock brackets.59TRANSPORTING THE BACKHOE60REMOVAL FROM TRACTOR - STORAGE601. Put stabilizers down and lift backhoe slightly. Rotate boom straight back.602. Install swing lock pin.603. Complete raise boom and lower dipperstick. Curl bucket until bottom of bucket is level with ground. Lower boom until bucket rests firmly on ground.604. Remove pins which secure backhoe to tractor.605. Lower front of subframe to rest on ground.606. Slowly drive forward until tractor clears backhoe. Engage tractor brakes.607. Lower backhoe by raising stabilizers and boom until backhoe or subframe rests on suitable blocking. Leave stabilizers touching ground.608. Shut off tractor. Work handles back and forth to relieve hydraulic pressure. Disconnect hydraulic lines or pump from backhoe.609. For long term storage, coat all exposed cylinder rods with grease.6010. Lubricate all grease fittings, stabilizer pivot pins and complete handle linkage.60MAINTENANCE SECTION611 O-RING 1692 O-RING 1693 VALVE BODY/RELIEF 1694 PISTON 1695 SPRING 1696 O-RING 1697 REGISTER 1698 NUT, M16-1.5 1699 DEFLECTOR 16910 O-RING 56911 CENTERING RING 56912 SPRING 56913 SPACER 106914 SCREW 56915 CAP 206916 SCREW 206917 SCREW 46918 CIRCLIP 16919 WASHER 16920 BUSHING 16921 SPRING 16922 BALL HOLDER 16923 STEEL BALL D.5 36924 STEEL BALL D.7 16925 CAP 16926 WASHER 16927 SPACER 16928 SPRING 16929 SPACER 16930 CENTERING RING 16931 O-RING 15.10 X 2.70 X 1.5 16932 PLUG 46933 COPPER GASKET 14 X 20 X 15 46934 REGISTER 46935 SPRING 46936 PISTON 46937 VALVE BODY/RELIEF 46938 O-RING 17.17 X 1.78 46939 O-RING 46940 PLUG 16941 O-RING 17.17 X 1.78 16942 O-RING 16943 PLUG 66944 SPRING 66945 O-RING 11.11 X 1.78 66946 BODY 66947 PLUG 16948 LEVER 26949 RUBBER BELLOWS 26950 HOUSING/LEVER 26951 O-RING 15.10 X 2.70 26952 CENTERING RING 26953 LEVER PIN 26954 SCREW 86955 O-RING 15.10 X 2.70 46956 NUT 36957 PLATE/JOYSTICK 16958 SCREW 86959 ASSEMBLY 26960 ASSEMBLY 26961 PIN 26962 FLANGE 16963 SCREW 66964 NUT, M7 46965 O-RING GASKET 26966 RUBBER BELLOWS 26967 SCREW 46968 ARICULATION 26969 NUT, M6 26970 FLANGE 16971 CENTERING RING 16972 O-RING 15.60 X 1.78 16973 PLATE/JOYSTICK 16974 VALVE BLOCK 16975 PLUG 169CYLINDER SERVICE62CYLINDER DISASSEMBLY621. Hold cylinder tube (13) stationary and pull wire ring (14) out through slot. Rotate head (6) to ease disassembly.622. Pull shaft (1), with all assembled parts, out of cylinder tube.623. Remove lock nut (12) from end of shaft and slide piston (8) and cylinder head (6) off shaft.624. Remove piston wear ring (11), piston seal (10) and o- ring (9) from outside grooves on piston (Swing cylinders have additional steel ring between piston and nut).625. Remove wiper seal (2), rod seal (3) and wear ring (7) from inside of cylinder head and o-ring (5) with backup washer (4) from groove on outside of head.626. Clean all parts including cylinder tube, in a suitable cleaning solvent, then use air pressure to blow any dirt or excess solvent from all parts.627. Examine all parts for wear or damage and replace, if necessary.62CYLINDER ASSEMBLY621. Place rod seal (3) into groove inside cylinder head.622. Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head. Install wear ring (7) inside other end of head.623. Place o-ring (5) with backup washer (4) in groove on outside of head. Backup washer must be on rod side.624. Remove sharp edges on outer edge of threaded end of shaft (1). Lubricate wiper seal (2) and rod seal (3) in head and carefully slide head onto shaft.625. Place o-ring (9), piston seal (10) and piston wear ring (11) in grooves on outside of piston.626. Slide piston onto threaded end of shaft and install lock nut (12). Swing, bucket and stabilizers cylinders; tighten lock nut (12) to 300 ft./lbs. Lift and dipperstick cylinders; tighten lock nut (12) to 375 ft./lbs. on lift cylinders.627. Lubricate piston wear ring (11) and piston seal (10) on piston, o-ring (5) and backup washer (4) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube.628. Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.62BEGINNING OF SEASON63HYDRAULIC HOSES63HYDRAULIC SYSTEM RESERVOIR63BUCKET TOOTH POINTS64TIGHTENING NUTS AND BOLTS64LUBRICATION64LUBRICATION CHART64HYDRAULIC TROUBLESHOOTING65VALVE SERVICE67MAIN RELIEF REPLACEMENT671. Use a socket to remove main relief from valve housing.672. Inspect new relief to ensure seal is properly installed, and apply grease around the relief.673. Ensure that pressure setting stamped on new relief matches the setting of old relief.674. Install o-rings on relief.675. Insert relief and torque to 60 ft./lbs.67SPOOL SEAL INSTALLATION671. Remove the mechanical joystick kit from the top of the valve and the return kit from the bottom.672. Remove the old o-rings and leave spool in housing, making sure spool is in center position.673. Lightly oil one seal and insert it in top of valve. Slide the seal into position in the groove in the valve body, making sure that it does not fall into the spool groove.674. Lightly oil a second o-ring and insert in bottom of valve. Slide the seal into position in the groove in the valve body making sure it does not fall into the spool groove. Do not push on the spool as it may cause the first seal to come out of the ...675. Reinstall the mechanical joystick kit on the top of the valve and return kit on the bottom.67TORQUE SETTINGS671. Main Relief Body: 60 ft./lbs.672. Load Check Valve: 15 ft./lbs.673. Screws: 4 ft./lbs.67PARTS LIST69PROPER TORQUE FOR FASTENERS70ALAMO SMC72LIMITED WARRANTY721. LIMITED WARRANTIES721.01. Alamo SMC warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that ...721.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.721.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...721.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.722. REMEDIES AND PROCEDURES.722.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.722.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based722.03. Purchaser is responsible for returning the goods in question to the Dealer.722.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:72(a) Repair or replace the defective goods or part(s) or72(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.722.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...723. LIMITATION OF LIABILITY.723.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.723.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.723.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...723.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.724. MISCELLANEOUS.724.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.724.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.724.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.724.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.72ALAMO SMC72TO THE OWNER/OPERATOR/DEALER73Taille: 2,4 MoPages: 74Language: EnglishOuvrir le manuel