BenutzerhandbuchInhaltsverzeichnisTable of Contents3Preface7Federal Communication Commission (FCC) Notices7Industry Canada (IC) Notices7Certified Bluetooth Module8Chapter 1: Introduction9General9Vehicle Detection10Autoscope RTMS Sx-300 Options11Autoscope RTMS Sx-300 Technical Specifications11Environmental Conditions14Electromagnetic Interference14Upgrade Capability14Chapter 2: Hardware Installation15General15Safety Information15Pre-Installation Considerations15Power Considerations15Cabling Considerations16Communications Considerations16Placement in Side-Fired Highway Configuration17Height and Setback Requirements19Zero Setback19Standard Setback19Guardrails and Barriers22Elevated Roadway23Sunken Road and Roadside Walls24Installing Autoscope RTMS Sx-300 on Sign Structures24Grade Differentials25Trees25Placement in Midblock Applications26Mounting and Aiming Procedure26Chapter 3: RTMS Setup Utility28General28System Requirements28Installing the Setup Utility29Starting the Setup Utility34For Networks With Only RTMS Sx-300 Sensors34For Multidrop Networks With RTMS Sx-300 and RTMS G4 Sensors36Navigating the Setup Utility37Running Demo Mode37Setup Utility Screens42Start Screen44Main Screen46Manual Setup Screen48Default Settings50Chapter 4: Configuration and Setup52General52Configuration Process52Required Equipment/Personnel52Step 1: Set the Application Mode53Step 2: Run the Wizard56Step 3: Adjust the Zones59Step 4: Verify Vehicle Counts61Step 5: Calibrate Speed66Step 5A: Setting the Reference Speed66Step 5B: Auto Calibration69Step 5C: Check Calibration69Step 6: Define Message Composition71Step 7: Define Vehicle Classifications74Step 8: Save the Configuration File78Chapter 5: Operations and Adjustments80General80Advanced Options80Changing the Data Mode81Common Setup Options84Defining Communications86Defining a Serial Connection88Defining a Bluetooth Connection90Defining a Dialup Connection92Defining a TCP/IP Connection94Changing an Existing Connection96Finding Sensors98Loading a Previously Saved Setup File101Manual Speed Calibration103Memory Operations104Defining Memory Options104Downloading Autoscope RTMS Sx-300 Memory106Clearing Memory109Message Operations110Defining the Message Composition110Defining Per Vehicle Messages110Changing the Message Period112Optimizing Volume Count Accuracy113Condition A: Over/Under Count in Adjacent Zones114Condition B: Under Count in Near Zone115Condition C: Under Count in Far Zone116Condition D: Under Count in Several Zones117Condition E: Over Count in Several Zones118Condition F: Under Count in First Zone Past a Barrier119Polling Sensors120Recording Data To a File123Self Test124Sensitivity Adjustment126Setting the Sensor ID127Updating the Setup Utility With a New Configuration128Upgrading Firmware128Viewing Statistics130Zone Setup131Adding/Deleting Zones132Adjusting Zone Boundaries134Assigning Labels to Zones137Chapter 6: Troubleshooting139General139Messages139Symptoms141Do’s and Don’ts144Technical Support145North American Users’ Resource145All Other Users’ Resources145Appendix A: Cabling and Connectors146General146Preparing a Cable147Connecting a Cable to the Autoscope RTMS Sx-300148Surge Suppression/Protection148Wiring Notes148MS Connector Pin Out148Standard Serial Port150Standard RS-232 Port Wiring150RS-485 Port Wiring151RS-485 Multi-Drop Wiring152Connecting Autoscope RTMS Sx-300 to External Modems152Modem Cables153Modem Sharing154Appendix B: Surge Protection155General155Breakout Boxes155Cabling to the Breakout Box156Cabling From the Breakout Box156Parts of the Surge Suppression Package156Power Line Protection156Communication Line Protection157Grounding159Providing a Proper Ground159Why Grounding is Important160Low Voltage Power161Autoscope RTMS Sx-300 Interface Panels162DIN Rail Power and RS-232 Interface Panel (P/N A600-1099)163DIN Rail Power and RS-232 & RS-422/485 Interface Panel (P/N A600-1098)164DIN Rail Power and RS-232 and TCP/IP Interface Panel (P/N A600-1097)165DIN Rail Power and RS-485 Interface Panel (P/N A600-1100)166Appendix C: Data Files and Message Formats167Traffic Data Files167Sample X3 Compatible Statistical Message169G4 Statistical Message170Statistical Message with Per Vehicle On171Appendix D: Bluetooth Device Operations173General173Method 1: Using the Sena Parani UD100-G03 USB Adapter174Determining if Your Computer Has Bluetooth Installed174Pairing With and Connecting to the Autoscope RTMS Sx-300174Disconnecting Bluetooth180Finding the Bluetooth COM Port Assignment181Method 2: Using Microsoft Windows182Determining if Your PC has Bluetooth Installed182Search For and Connect to A Bluetooth Device182Finding the Bluetooth COM Port Assignment187Changing the Bluetooth COM Port Assignment188Changing the Bluetooth Password/Passkey191Appendix E: Speed Calibration Worksheet193General193Glossary195Index198Numerics198A198B198C198D198E199F199G199H199I199L199M199N200O200P200R200S200T201U201V201W201X201Y201Z201Reader’s Comment Form202Größe: 5,38 MBSeiten: 203Language: EnglishHandbuch öffnen
