Panasonic AJ-HD1700PE User Manual
85
Setup menus
The underlining (__) denotes the factory setting mode.
<OPERATION>
(continued)
113*
1
REC INH
For selecting whether to allow or inhibit recording
on the cassette tape.
on the cassette tape.
0000
OFF:
Recording on the cassette tape is enabled when the
cassette’s accidental erasure prevention mechanism
has been set to the recording enable position.
cassette’s accidental erasure prevention mechanism
has been set to the recording enable position.
0001
ALL:
All recording on the cassette tape is inhibited.
0002
PRE:
Overwriting is inhibited during normal recording.
This is the setting to activate the accidental erasure
prevention function. While CTL is detected, the
recording is inhibited, and when CTL cannot be
detected, it is executed.
This is the setting to activate the accidental erasure
prevention function. While CTL is detected, the
recording is inhibited, and when CTL cannot be
detected, it is executed.
0003
NORM:
Normal recording is inhibited.
Use this setting when it is preferable to avoid
using normal recording in all applications
except for editing.
Use this setting when it is preferable to avoid
using normal recording in all applications
except for editing.
0004
V/CTL:
The recording of the video and CTL signals is
inhibited.
Use this setting when it is preferable to avoid editing
in all applications except for audio editing.
inhibited.
Use this setting when it is preferable to avoid editing
in all applications except for audio editing.
<Note>
When the PRE, NORM or V/CTL setting has been
selected, the REC INHIBIT lamp blinks (on for approx.
0.5 sec. and then off for approx. 0.5 sec.).
When the PRE, NORM or V/CTL setting has been
selected, the REC INHIBIT lamp blinks (on for approx.
0.5 sec. and then off for approx. 0.5 sec.).
No./Item
Description of setting
1
2
3
4
Description of MEMORY STOP function
The MEMORY STOP function does
not work if this margin is less than
not work if this margin is less than
d
2 frames.
FF
button
button
0 point
FF
button
button
REW
button
button
REW
button
button
!
If the FF button is pressed, the normal FF operation is performed
since there is no 0 point in the direction of this operation.
since there is no 0 point in the direction of this operation.
@
If the REW button is pressed, the PREROLL lamp lights (as does
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
#
If the REW button is pressed, the normal REW operation is
performed since there is no 0 point in the direction of this
operation.
performed since there is no 0 point in the direction of this
operation.
$
If the FF button is pressed, the PREROLL lamp lights (as does
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
114
REC INH
LAMP
LAMP
For selecting whether the REC INHIBIT lamp is to
blink or light when the cassette tape has been set
to the accidental erasure protection mode.
blink or light when the cassette tape has been set
to the accidental erasure protection mode.
0000
LIGHT:
The lamp lights.
0001
FLASH:
The lamp blinks.
<Note>
If 1 (ALL) has been selected as the setup menu item
No.113 (REC INH) setting, the REC INHIBIT lamp will
be lighted at all times regardless of the REC INH LAMP
setting.
If 1 (ALL) has been selected as the setup menu item
No.113 (REC INH) setting, the REC INHIBIT lamp will
be lighted at all times regardless of the REC INH LAMP
setting.
115*
1
EJECT SW
INH
INH
For selecting whether to enable or disable the
operation of the EJECT button on the VTR’s
front panel.
operation of the EJECT button on the VTR’s
front panel.
0000
REC:
Operation is disabled while the
VTR is in the recording mode.
VTR is in the recording mode.
0001
OFF:
Operation is enabled in all
modes.
modes.
Accidental erasure protection function
This function is used to prevent parts already recorded on a tape from being
recorded over. Accidental erasure of pre-recorded tapes is prevented by
positioning the CTL signal rec/play heads as shown in the figure below so that
whether a recording has been made can be determined by the presence or
absence of the CTL signal. When the REC/PLAY button is pressed with a pre-
recorded tape, the tape runs but the REC button lamp blinks, the beeping
alarm is sounded, and no signals are recorded.
recorded over. Accidental erasure of pre-recorded tapes is prevented by
positioning the CTL signal rec/play heads as shown in the figure below so that
whether a recording has been made can be determined by the presence or
absence of the CTL signal. When the REC/PLAY button is pressed with a pre-
recorded tape, the tape runs but the REC button lamp blinks, the beeping
alarm is sounded, and no signals are recorded.
Rough sketch showing CTL head positions
PRE CTL
head
A/C heads
(rec/play heads)
(rec/play heads)
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.
(SYSTEM FREQ) setting.
No./Item
Description of setting
112
FRZ MODE
SEL
SEL
For selecting what playback images are to be
output in the STANDBY OFF mode and EJECT
mode.
output in the STANDBY OFF mode and EJECT
mode.
0000
DIS:
The video output is muted.
0001 STB OFF:
Only when the STANDBY OFF mode is
established is the image which was being
played back at that moment frozen and output.
established is the image which was being
played back at that moment frozen and output.
0002 SOF&EJ:
When either the STANDBY OFF mode or the
EJECT mode is established, the image which
was being played back at that moment is
frozen and output.
EJECT mode is established, the image which
was being played back at that moment is
frozen and output.
<Notes>
• The status when the picture is frozen is determined
• The status when the picture is frozen is determined
by the setup menu item No.604 (FREEZE SEL)
setting.
setting.
• In the EJECT mode, the frozen picture is output only
when 1 (BLACK) or 2 (GRAY) has been selected as
the setup menu item No.106 (EJECT EE SEL)
setting.
the setup menu item No.106 (EJECT EE SEL)
setting.
• The picture freeze is forcibly released if a change has
occurred in the output format of the HD serial output
signals when operation has transferred to the EJECT
mode.
signals when operation has transferred to the EJECT
mode.