Philips CDR570/00 User Manual

17

Important:
- Recording from CD-changers should always be started in the

RECORD DISC, RECORD TRACK or MAKE CD mode.

- Only make analog recordings when digital recording is not

possible.

1 Make sure the disc is absolutely free of scratches and dust

particles.

2 Press SOURCE repeatedly until (depending on the

connection used):
➜ DIGITAL I d, OPTICAL I p or ANALOG a lights up

and 

DIGITAL 1, OPTICAL or ANALOG appears on

the display.

• When Auto Track is ON (default setting), track numbers will

automatically be increased during recording. 

• To switch off the Auto Track function you have to enter

Menu mode.
If you wish to increase track numbers manually, press
TRACK INCR(ement) on the remote control. For further
instructions see Menu mode.

ON (AUTO): The track increments are automatically taken over

from the digital source material or after 2.7
seconds silence during analog recording.

OFF (MANUAL): Track numbers can be incremented manually

by pressing TRACK INCR(ement) on the
remote control. (Minimum track length is 4
sec.) (This can also be done in Auto mode.)

• Track numbers cannot be changed after recording.

Note: Auto track works only with Consumer Sources with a

digital output signal according to the IEC 958
(consumer part) audio standard.

3 With the recorder stopped, press REC TYPE three times to

enter the Manual Record standby mode.
➜ 

starts to flash and the display shows 

REC

MANUAL.

• If 

CHECK INPUT message also flashes, the digital

connection is incorrect.

4 Play the source first to set the optimal recording level on

the CD recorder.

5 Rotate the EASY JOG/ENTER key until, on the Record/Play

Level bar, all the blue segments are alight, but the red
segments do not light continuously during the loudest
passages.
➜ Display shows 

_XX DB.

6 Stop the source.

1 To start recording, press RECORD on the CD recorder and

immediately start the source (from Stop-mode).
➜ d lights continuously. The track number and recording

time appear on the display.

• To record a 3-second silence at the start of a track, press

PAUSE on the CD recorder before starting the source.

• To check the elapsed recording time, press DISPLAY on the

CD recorder. (This can also be done during the recording.)

2 To stop recording, press STOP on the CD recorder.

➜

WAIT lights up and d goes out.

• If STOP was pressed within 3 seconds after RECORD, no

recording will take place.

• To interrupt recording, press PAUSE on the CD recorder. 

d starts to flash. Resume at step 1.

After recording the display will show 

UPDATE for several

seconds.

Note: With 

AUTO TRACK ON, the recorder will stop and go

to REC STANDBY for 1 minute and then goes to stop
mode automatically. Recordings from DAT, DCC or
recordings made analogously will stop after 20 seconds
silence. With 

AUTO TRACK OFF, the auto stop

mode is disabled.

DIGITAL

OPTICAL

ANALOG

I
I

CD

SYNC

PROGRAM

SHUFFLE REPEAT

SCAN

ALL

MANUAL

TRACK

RW

REM

TRACK

REC

TIME

REM

TOTAL

TIME

STEP

TRACK

FADE

DIGITAL

OPTICAL

ANALOG

I
I

CD

SYNC

PROGRAM

SHUFFLE REPEAT

SCAN

ALL

MANUAL

TRACK

RW

REM

TRACK

REC

TIME

REM

TOTAL

TIME

STEP

TRACK

FADE

CDR 

MINI AUDIO
CD RECORDER

OPEN/CLOSE

EASY JOG

REWIND

RECORD

REC TYPE

MENU/STORE

CANCEL

SOURCE

PLAY/PAUSE

STOP

FFWD

ERASE

FINALIZE

SCROLL

DISPLAY

Recordable

1

2

3

4

5

6

7

8

9

ANALOG

CD

RW

10 11 12 13 14

15 16

ENTER