Panasonic KX-PRW110FX User Manual
6
Edit the text memo if necessary (30
characters max.). a MOKN
characters max.). a MOKN
7
MbN: Select the desired alarm tone. a
MOKN 2 times a M
MOKN 2 times a M
N
Erasing an entry
Schedule alarm entries are not erased
automatically after the schedule alarm sounds.
Erase unwanted entries.
automatically after the schedule alarm sounds.
Erase unwanted entries.
1
MMenuN (right soft key) a
a MOKN
2
MListN a MbN: Select the desired entry.
3
MMenuN a MbN: “Erase” a MOKN
4
MbN: “Yes” a MOKN a M
N
Erasing all entries
1
MMenuN (right soft key) a
a MOKN
2
MListN a MMenuN
3
MbN: “Erase All” a MOKN
4
MbN: “Yes” a MOKN
5
MbN: “Yes” a MOKN a M
N
Registering a unit
Operating additional units
Additional handsets
Up to 6 handsets can be registered to a single
base unit.
Important:
R The additional handset model
base unit.
Important:
R The additional handset model
recommended for use with this unit is noted
on page 4. If another handset model is
used, certain operations may not be
available.
on page 4. If another handset model is
used, certain operations may not be
available.
Additional base units
Handsets can be registered to up to 4 base
units, allowing you to add additional base units
and extend the area in which your handset(s)
can be used. If a handset moves out of range
of its base unit when “Auto” is selected on
units, allowing you to add additional base units
and extend the area in which your handset(s)
can be used. If a handset moves out of range
of its base unit when “Auto” is selected on
base unit (page 33), it looks for another
base unit to make or receive calls. A base unit
and the handsets it communicates with is
called a “radio cell”.
Note:
R Calls are disconnected when the handset
base unit to make or receive calls. A base unit
and the handsets it communicates with is
called a “radio cell”.
Note:
R Calls are disconnected when the handset
moves from one radio cell to another.
Registering a handset to a base
unit
unit
The supplied handset and base unit are
pre-registered. If for some reason the handset
is not registered to the base unit (for example,
pre-registered. If for some reason the handset
is not registered to the base unit (for example,
is displayed even when the handset is
near the base unit), re-register the handset.
1
Handset:
MMenuN (right soft key) #130
MMenuN (right soft key) #130
2
MbN: Select a base unit number. a MOKN
R This number is used by the handset as
R This number is used by the handset as
a reference only.
3
Base unit:
Press and hold M
Press and hold M
N for about 5 seconds.
R If all registered handsets start ringing,
press M
N again to stop, then repeat
this step.
4
Handset:
MOKN a Wait until “Base PIN” is
displayed. a Enter the base unit PIN
(default: “0000”). a MOKN
R If you forget your PIN, contact an
MOKN a Wait until “Base PIN” is
displayed. a Enter the base unit PIN
(default: “0000”). a MOKN
R If you forget your PIN, contact an
authorised service centre.
Selecting a base unit
When “Auto” is selected, the handset
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
1
MMenuN (right soft key) #137
2
MbN: Select the desired base unit number,
or “Auto”. a MOKN
or “Auto”. a MOKN
33
Programming
PRW110FX(en)_0724_ver012.pdf 33
2013/07/24 13:40:26