Pelco C1300M-C (11/08) User Manual
C1300M-C (11/08)
29
Quick Programming Guide
(See Page 9)
ENABLE MOTION DETECTION (23X DAY/NIGHT CAMERA)
The following are the settings for MOTION DETECTION ENABLED:
NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.
EDIT DETECTION AREAS (23X DAY/NIGHT CAMERA)
Four motion detection areas can be defined for a preset. Use the following steps to edit motion
detection areas.
detection areas.
1.
Edit detection areas 1, 2, 3, or 4:
a.
Use the joystick to position the cursor beside EDIT DETECTION AREAS.
b.
Press Iris Open. The EDIT DETECTION AREAS programming window appears on the monitor.
c.
Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3, or 4.
d.
Press Iris Open. The cursor moves to the right next to the number 0.
e.
Move the joystick up. A blue rectangle appears in the upper left-hand corner of the screen.
f.
Use the joystick to place the blue rectangle over the desired detection area.
g.
Press Iris Open to make a selection.
NOTE: Motion detection is not guaranteed to catch 100% of activity.
2.
Set the sensitivity of the motion detection area:
a.
Position the cursor next to SENSITIVITY for DETECTION
AREA 1, 2, 3, or 4.
AREA 1, 2, 3, or 4.
b.
Press Iris Open, the cursor moves to the right.
c.
Use the joystick to select one of the following sensitivity
levels:
levels:
d.
Press Iris Open to make selection.
EXIT
LANGUAGE
ENGLISH
UNIT INVERSION
OFF
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
CYCLE CAMERA POWER
REBOOT SYSTEM
PELCO EXSITE IPSXM
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT
EXIT
UNIT SETTINGS
PRESET NUMBER
1
***PRESET NOT DEFINED***
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<MOTION DETECTION>*
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<MOTION DETECTION>*
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
EXIT
REFERENCE INFORMATION
AZIMUTH
AZIMUTH
--
ELEVATION
--
ZOOM
--
CUSTOM CAMERA SETTINGS
--
PRESETS
MOTION DETECTION ENABLED
OFF
<EDIT DETECTION AREAS>
ACTIVATE AUX
OFF
AUX TIME (SECS)
0
BACK
EXIT
EXIT
MOTION DETECTION*
* Available only with the 23X day/night camera.
OFF (default)
Motion detection is turned off (disabled).
ON
Motion detection is turned on (enabled).
HIGH
The sensitivity level is high. Slight
changes in light level and contrast
are detectable.
changes in light level and contrast
are detectable.
MEDIUM (default)
Average sensitivity.
LOW
The sensitivity level is low.
MOTION DETECTION AREAS
EDIT DETECTION AREAS*
DETECTION AREA 1
LOCATION
LOCATION
0
SENSITIVITY
MEDIUM
DETECTION AREA 2
LOCATION
LOCATION
0
SENSITIVITY
MEDIUM
DETECTION AREA 3
LOCATION
LOCATION
0
SENSITIVITY
MEDIUM
DETECTION AREA 4
LOCATION
LOCATION
0
SENSITIVITY
MEDIUM
BACK
EXIT
EXIT