Panasonic AJ-P2C004HG User Manual
43
Recording and Playback: Recording Review Function
Re
co
co
rd
in
g an
d P
lay
lay
ba
ck
ck
Sound
By selecting “ON”/“OFF” for the menu option AUDIO REC
in the <REC FUNCTION> screen, it is possible to specify
whether or not sound will be recorded during interval
recording.
By selecting “ON”/“OFF” for the menu option AUDIO REC
in the <REC FUNCTION> screen, it is possible to specify
whether or not sound will be recorded during interval
recording.
Record/playback buttons
During interval recording, all operation buttons other than
STOP (REW, FF, PLAY/PAUSE) are disabled. However,
during a pause in ONE SHOT mode, REC REVIEW can
be executed with the RET button on the lens.
During interval recording, all operation buttons other than
STOP (REW, FF, PLAY/PAUSE) are disabled. However,
during a pause in ONE SHOT mode, REC REVIEW can
be executed with the RET button on the lens.
If the POWER switch is turned [OFF] during recording
If the unit is turned off during interval recording, the video
stored in memory is recorded onto the P2 card, and then
the unit automatically turns off.
If the unit is turned off during interval recording, the video
stored in memory is recorded onto the P2 card, and then
the unit automatically turns off.
To start emergency recording during a pause
If the REC START/STOP button is assigned to one of the
USER MAIN, USER 1, USER 2, MARKER SELECT and
TEXT MEMO button in advance, emergency recording
can be started during a pause by holding down the
relevant button. Pause time measurement continues after
such emergency recording.
If the REC START/STOP button is assigned to one of the
USER MAIN, USER 1, USER 2, MARKER SELECT and
TEXT MEMO button in advance, emergency recording
can be started during a pause by holding down the
relevant button. Pause time measurement continues after
such emergency recording.
Note
However, this function does not work in native recording with
VFR operation.
VFR operation.
Time code indication
When recording starts, the time code (TCG) display may
not update until the unit recognizes the P2 card.
When recording starts, the time code (TCG) display may
not update until the unit recognizes the P2 card.
Removing cards
During INTERVAL REC mode operation, the P2 card
access LED for the target P2 card blinks in orange. Do not
remove the P2 card during this status. If you should
remove the card accidentally, restore clips. However, even
if the clips are restored, the last 3 to 4 seconds of the
recording (up to a maximum of about 10 seconds if the P2
card is removed while recording onto multiple P2 cards)
may be lost. For more information on how to fix clips, see
[Restoring Clips] (page 129).
During INTERVAL REC mode operation, the P2 card
access LED for the target P2 card blinks in orange. Do not
remove the P2 card during this status. If you should
remove the card accidentally, restore clips. However, even
if the clips are restored, the last 3 to 4 seconds of the
recording (up to a maximum of about 10 seconds if the P2
card is removed while recording onto multiple P2 cards)
may be lost. For more information on how to fix clips, see
[Restoring Clips] (page 129).
Thumbnail operation and menu operation
Thumbnail operation does not work during the INTERVAL
REC mode operation. Press the STOP button before
operating thumbnails.
When standby time is set to 1 minute or more or when in
ONE SHOT mode, the following restrictions apply even
though the menu can be operated during stand-by mode.
– The respective settings of SYSTEM MODE, REC
Thumbnail operation does not work during the INTERVAL
REC mode operation. Press the STOP button before
operating thumbnails.
When standby time is set to 1 minute or more or when in
ONE SHOT mode, the following restrictions apply even
though the menu can be operated during stand-by mode.
– The respective settings of SYSTEM MODE, REC
FORMAT, CAMERA MODE, PC MODE and VFR
cannot be changed.
cannot be changed.
– The respective settings for SD CARD READ/WRITE,
LENS FILE CARD R/W, READ USER DATA, and READ
FACTORY DATA cannot be executed.
FACTORY DATA cannot be executed.
When recording is paused, pressing the RET button
automatically locates the last 2 seconds of video just
recorded, and the viewfinder provides video playback. Thus,
it is possible to check whether the recording has been
performed correctly.
After playback, the unit is again ready to start recording.
The picture location/playback duration can be increased to
up to 10 seconds by continuously pressing the RET button.
For short clips, however, when the start of a clip is located,
continuously pressing the RET button does not play back
any clips before that clip.
automatically locates the last 2 seconds of video just
recorded, and the viewfinder provides video playback. Thus,
it is possible to check whether the recording has been
performed correctly.
After playback, the unit is again ready to start recording.
The picture location/playback duration can be increased to
up to 10 seconds by continuously pressing the RET button.
For short clips, however, when the start of a clip is located,
continuously pressing the RET button does not play back
any clips before that clip.
The function of the RET button may be assigned to a
desired user button by using one of the menu options USER
MAIN SW, USER1 SW, USER2 SW, MARKER SEL or
TEXT MEMO SW. These options can be found in the
<USER SW> screen on the CAM OPERATION page.
When recording is paused, pressing the PLAY/PAUSE
button plays back the last recorded clip, from the beginning.
After completion of playback, the unit enters the stopped
state.
desired user button by using one of the menu options USER
MAIN SW, USER1 SW, USER2 SW, MARKER SEL or
TEXT MEMO SW. These options can be found in the
<USER SW> screen on the CAM OPERATION page.
When recording is paused, pressing the PLAY/PAUSE
button plays back the last recorded clip, from the beginning.
After completion of playback, the unit enters the stopped
state.
Notes
Set the menu option RET SW (found in the <SW MODE>
screen on the CAM OPERATION page) to “R.REVIEW”.
When the HD SDI A · B switch on the side panel is
positioned at [MEM], the video for REC REVIEW is output
from the video output connectors (HD SDI A · B and MON
OUT connectors), and also to the viewfinder.
Note that when a backup device is connected to back up
the video the pictures for REC REVIEW are backed up.
screen on the CAM OPERATION page) to “R.REVIEW”.
When the HD SDI A · B switch on the side panel is
positioned at [MEM], the video for REC REVIEW is output
from the video output connectors (HD SDI A · B and MON
OUT connectors), and also to the viewfinder.
Note that when a backup device is connected to back up
the video the pictures for REC REVIEW are backed up.
During INTERVAL REC mode general notes
Recording Review Function
The PLAY/PAUSE button plays back the
clip from the beginning.
clip from the beginning.
Recording starts
Recording pauses
The RET button puts the unit into REC
REVIEW mode.
REVIEW mode.
2-10 Seconds
Recorded clip
AJ-HPX2700G-VQT1V27_eng.book 43 ページ ２００８年９月２日 火曜日 午後５時４３分