Panasonic AJ-P2C004HG User Manual
46
Adjustments and Settings for Recording: Multi Format
Adjustments and Settings for Recording
The unit employs a progressive scan (full pixel reading) CCD system.
With combinations of the SYSTEM MODE and CAMERA MODE menu options on the <SYSTEM MODE> screen on the
SYSTEM SETTING page, you can select an video system from among 23 types.
In any video system, the CCD operates in progressive (non-interlace) scan mode.
With combinations of the SYSTEM MODE and CAMERA MODE menu options on the <SYSTEM MODE> screen on the
SYSTEM SETTING page, you can select an video system from among 23 types.
In any video system, the CCD operates in progressive (non-interlace) scan mode.
SYSTEM MODE menu option
Allows you to select a combination of system frequency
(59.94 Hz, 50 Hz, 60 Hz, 23.98 Hz and 24 Hz) and
signaling system (1080i or 720P). When a change has
been made to the SYSTEM MODE option, the
viewfinder indicates “TURN POWER OFF”. Then, turn
the POWER switch of the unit off and wait 5 seconds or
longer before turning the unit on again.
(59.94 Hz, 50 Hz, 60 Hz, 23.98 Hz and 24 Hz) and
signaling system (1080i or 720P). When a change has
been made to the SYSTEM MODE option, the
viewfinder indicates “TURN POWER OFF”. Then, turn
the POWER switch of the unit off and wait 5 seconds or
longer before turning the unit on again.
CAMERA MODE menu option
Selecting a shooting mode when the signal format is
1080i. For information about the behavior for each
setting, see [Recording formats and output connector
signal formats] (page 47).
1080i. For information about the behavior for each
setting, see [Recording formats and output connector
signal formats] (page 47).
Note
When the camera has been switched from 60i, 60P, or
30P to 24P or 24PA, video may produce noise for a
moment because the pull-down 5-frame cycle is
adjusted. This is not an abnormal condition.
30P to 24P or 24PA, video may produce noise for a
moment because the pull-down 5-frame cycle is
adjusted. This is not an abnormal condition.
REC FORMAT menu option
Used to select the recording format
AVC-I 100
The AVC-Intra100 format is used to record
video. The native recording format applies to
the 30PN, 24PN and 25PN modes.
video. The native recording format applies to
the 30PN, 24PN and 25PN modes.
AVC-I 50
The AVC-Intra50 format is used to record
video. The native recording is applied to the
30PN, 24PN and 25PN modes.
video. The native recording is applied to the
30PN, 24PN and 25PN modes.
DVCPROHD
The DVCPRO HD format is used to record
video. The native recording is for the 30PN,
24PN and 25PN modes.
video. The native recording is for the 30PN,
24PN and 25PN modes.
Note
When “AVC-I 50” or “AVC-I 100” is selected, the 24PA
mode cannot be selected.
mode cannot be selected.
VFR menu option
When the signal format is 720P, you can select whether
to perform VFR recording.
to perform VFR recording.
ON
Enables variable frame rate shooting at the
frame rate set in FRAME RATE.
frame rate set in FRAME RATE.
OFF
The frame rate is determined according to the
REC FORMAT setting.
REC FORMAT setting.
FRAME RATE menu option
When the VFR menu option is set to “ON”, it is possible
to shoot using the frame rate set in this menu option.
When the VFR menu option is set to “ON”, pressing the
jog dial button displays the frame rate on the upper left
of the viewfinder screen as a blinking number. It is then
possible to change the frame rate setting without
opening the FRAME RATE menu option by pressing the
SYNCHRO SCAN adjustment buttons (+/-). Note,
however, that this operation is not available when the
FRATE function has been set to on using a user button.
to shoot using the frame rate set in this menu option.
When the VFR menu option is set to “ON”, pressing the
jog dial button displays the frame rate on the upper left
of the viewfinder screen as a blinking number. It is then
possible to change the frame rate setting without
opening the FRAME RATE menu option by pressing the
SYNCHRO SCAN adjustment buttons (+/-). Note,
however, that this operation is not available when the
FRATE function has been set to on using a user button.
Multi Format
Video system and Recording format
Selecting a recording signal and method
AJ-HPX2700G-VQT1V27_eng.book 46 ページ ２００８年９月２日 火曜日 午後５時４３分