Panasonic AG-HPX600EN User Manual

– 157 –

If an error is detected immediately after the camera turns on or during operation, the <WARNING> lamp and the lamp on the viewfinder screen indicate 
the error.

1

System error

[SYSTEM ERROR] factor 

display*

1

 flashes in red.

Flashes four 

times every 

second

Flashes four 

times every 

second

Error in the P2 microcomputer 

or control. The current operation 

will stop.

Check the factor display*

1

 

and consult the place of 

purchase.

2

P2 card removal 

error

[TURN POWER OFF] flashes 

in red.

Flashes four 

times every 

second

Flashes four 

times every 

second

An error occurred in the built-in 

memory because the P2 card 

being accessed was ejected. 

Both of the access LEDs flash in 

orange.

Turn off the power. If the 

clip in the ejected P2 card 

contains errors, fix the 

errors.

3

Battery empty

[LOW BATTERY] flashes in red 

and an empty remaining battery 

indicator bar flashes. (Displayed 

even if its display setting is turned 

off in the setting menu.)

Flashes once 

every second

illuminated

The battery has run out. 

Recording and playback will stop. 

If the voltage drops further, the 

power is automatically turned off.

Change the batteries.

4

P2 card fully 

recorded

[  FULL] flashes in red.

Flashes four 

times every 

second after 

the recording 

finishes

Lights up after 

the recording 

finishes

The P2 card space is used up. 

Recording will stop.*

3

Delete some clips or insert 

a new card.

5

Recording error [REC WARNING] factor display*

2

 

flashes in red.

Flashes four 

times every 

second

Flashes four 

times every 

second

Error in recording.

The recording may stop or 

continue.*

4

Turn off the power and on 

again, and then check your 

recording and playback. 

If the recording operation 

fails, change the P2 card.

6

Corruption of 

standard signal

[TEMPORARY PAUSE 

IRREGULAR FRM SIG] flashes 

in red.

Flashes four 

times every 

second

Flashes four 

times every 

second

Correct recording is not 

possible due to corruption of the 

<GENLOCK IN> input signal, 

and the recording is suspended 

temporarily. The clip will be 

divided.

 

f

Recording resumes when 

the signal returns to normal. 

However, recording does not 

resume in interval recording, 

one-shot recording, and loop 

recording.

Check the <GENLOCK IN> 

signal.

7

Low wireless 

signal reception [WIRELESS RF] flashes in red.

Flashes four 

times every 

second (for 

recording only)

Flashes four 

times every 

second

The error indicates poor 

wireless audio reception 

condition. Recording continues 

without receiving the wireless 

microphone signal.

Check the microphone 

power supply and the 

reception status of the 

wireless receiver.

8

Battery nearly 

empty

One remaining battery indicator 

bar flashes. (Also displayed when 

the [OTHER DISPLAY] item 

on the setting menu [DISPLAY 

SETUP] screen is set to [OFF].)

Flashes once 

every second

Flashes once 

every second

The battery is about to run out.

The current operation will 

continue.*

5

Change the batteries as 

needed.

9

P2 card nearly 

full

The remaining P2 card capacity 

indicator flashes.

Flashes 

once every 

second during 

recording.

Flashes 

once every 

second during 

recording.

The remaining P2 card capacity 

is two minutes or less (the 

remaining indicator display is less 

than one minute). This warning is 

issued only during recording.

Change the P2 cards 

as needed or insert an 

additional card.

*1  [P2 SYSTEM ERROR] factor display

 

f

[P2 MICON ERROR]: P2 microcomputer is not responding.

 

f

[P2 CONTROL ERROR]: Error occurred in the P2 recording control.

 

f

[CAM MICON ERROR]: Camera microcomputer is not responding.

*2  [REC WARNING] factor display

 

f

[CARD ERROR*]: Error in P2 card (the slot number of the error card is displayed on *). Recording will stop.

 

f

[REC RAM OVERFLOW]: Recording RAM overflow. Recording will stop.

 

f

[PULL DOWN ERROR]: Image pull-down error in 24P, 25P, and 30P. Recording continues.

 

f

[OVER MAX NUMBER CLIPS]: An attempt was made to record more than the maximum number of clips (1000) to one P2 card.

 

f

[ERROR]: Other recording errors.

*3  The warning stops if the following operations are made.

 

f

Press the playback related buttons.

 

f

Press the <THUMBNAIL> button.

 

f

Eject the P2 card or insert another card.

*4  The warning stops if the following operations are made.

 

f

Press the <REC> button.