Panasonic AG-HPX600EN User Manual

– 158 –

 

f

Press the playback related buttons.

 

f

Press the <THUMBNAIL> button.

 

f

Eject all the cards.

*5  The warning can be stopped by setting the [NEAR END CANCEL] item to [ON] and pushing the <DISP/MODE CHK> switch towards the <CHK> side.

Indicates the error code on the [HOME] screen of SmartUI when something has caused an error on the camera. Check the types of warning, and deal 
with the error according to “Warnings description list” (page 157).

E-27

Recording control error (viewfinder screen [P2 CONTROL ERROR])

1. System error

E-30

P2 card removal error (viewfinder screen [TURN POWER OFF])

2. Card removal error

E-38

P2 streaming microcontroller error (viewfinder screen [P2 MICON 

ERROR])

1. System error

E-3F

Camera unit error (viewfinder screen [CAM MICON ERROR])

1. System error

E-40

Error in image sequence, generator lock input signal, or SDI input 

signal (viewfinder screen [IRREGULAR FRM SIG], [PULL DOWN 

ERROR])

5. Recording error, 6. Reference signal error

00000011

Recording error to P2 cards, etc. (viewfinder screen [REC RAM 

OVERFLOW], [CARD ERROR*], [OVER MAX# CLIPS], [ERROR])

5. Recording error

E-70

The directory structure on the P2 card is 

not supported. ([DIR ENTRY NG CARD] 

(slot number) is displayed on the viewfinder 

screen.)

Operation continues, but immediately back 

up data on the card, and format the card 

before using it again.

The warning code is displayed on 

the [HOME] screen of SmartUI.

E-71

The maximum number of overwrites on the 

P2 card has been exceeded. ([RUN DOWN 

CARD] (slot number) is displayed on the 

viewfinder screen.)

Operation continues, but recording 

or playback may not be performed 

properly. Replacement of the P2 card is 

recommended.

r

CANNOT ACCESS!

Data cannot be accessed due to a content defect or some 

other reason.

Ensure the health of the media and the clips.

CANNOT CHANGE!

For a clip with the [

] mark, where a thumbnail cannot be 

generated with AVC-Intra 100 or AVC-Intra 50, the thumbnail 

cannot be modified in the text memo position.

Set the [SYSTEM MODE] item on the setting menu [SYSTEM 

SETUP] screen according to the clips.

CANNOT COPY!

Images cannot be copied.

Check the copy conditions.

CANNOT DELETE!

Images cannot be deleted due to contents version mismatch.

Match the device and contents version.

CANNOT FORMAT!

A P2 card problem or some other reason prevents formatting. Check the P2 card.

CANNOT RE-CONNECT!

Clips cannot be remerged because either clips that are not 

recorded across multiple P2 cards are selected or other 

reasons.

Check the selected content.

CANNOT REPAIR!

Clips cannot be restored because contents that cannot be 

restored are selected or other reasons.

Check the selected content.

LACK OF CAPACITY!

There is not enough recording capacity left on the card.

Insert a card with sufficient recording capacity.

MISSING CLIP!

When all necessary P2 cards are not inserted, an attempt is 

made to add a shot mark to the clips recorded across multiple 

P2 cards.

Insert all P2 cards with the recorded clips and ensure that the 

[ ] incomplete clip indicator disappears, and then add the 

shot mark.

NO CARD!

No P2 or SD card is inserted.

Insert the relevant medium.

NO COPY TO SAME CARD!

A clip cannot be copied to the card storing the original clip.

Copy the selected clip to a card that does not contain the 

original clip.

NO FILE!

The specified file does not exist.

Check the file.

SAME CLIP IS SELECTED!

Clips cannot be copied because the clips already copied and 

the original clips are selected.

Check the selected clips, and remove either the original clips 

or copied clips, and then perform the copy operation.

TOO MANY CLIPS!

Too many clips are selected.

Reduce the number of selected clips.

UNKNOWN CONTENTS 

FORMAT!

Contents version is mismatched.

Match the device and content versions.

UNKNOWN DATA!

The metadata character code is invalid.

The metadata character code is UTF-8. Enter valid characters 

using a viewer.

USER CLIP NAME MODIFIED!

Characters in the clip name had to be deleted when adding a 

counter value.

For the counter addition setting, the user clip name plus the 

counter value can only contain up to 100 bytes. Characters in 

the clip name are automatically deleted when the total number 

of characters exceeds this limit.

WRITE PROTECTED!

The P2 or SD card is write-protected.

Insert write-enabled media.