Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 4.0 Remote Radio Transmitter Operations
EN | 21
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
Before a hand-held radio transmitter can operate the
control panel, you must teach the transmitter’s radio
code to the control panel. Refer to Section 4.3
Changing or Deleting Remote Radio User Codes for more
information.
control panel, you must teach the transmitter’s radio
code to the control panel. Refer to Section 4.3
Changing or Deleting Remote Radio User Codes for more
information.
4.1
Indications from Remote Radio
Transmitter Operations
Transmitter Operations
When using the 2-channel or 4-channel hand-held
transmitter to operate the system, audible or visual
indications, or both, can be provided by the horn
speakers or the strobe. These indications allow you to
operate the system from outside the premises with
confidence. The installer can program audible and
visual indication beeps by selecting Options 4 and 8
in Location 492 (refer to Section 18.1 System Options 1
on page 80). You can adjust the speaker beep volume
in Location 491 (refer to Section 17.15).
transmitter to operate the system, audible or visual
indications, or both, can be provided by the horn
speakers or the strobe. These indications allow you to
operate the system from outside the premises with
confidence. The installer can program audible and
visual indication beeps by selecting Options 4 and 8
in Location 492 (refer to Section 18.1 System Options 1
on page 80). You can adjust the speaker beep volume
in Location 491 (refer to Section 17.15).
Table 16: Horn Speaker Indication Beeps for
Remote Operations
No of Beeps
System Status
One System
disarmed
Two
System armed in AWAY Mode
One two-tone beep
System armed in STAY Mode 1
Table 17: Strobe Indications for Remote
Operations
Strobe Duration
System Status
3 sec
System disarmed
6 sec
System armed in AWAY Mode
6 sec
System armed in STAY Mode 1
4.2
Remote Radio User Code Priority
Levels
Levels
You can program the remote radio hand-held
transmitters to operate only as User Codes 9 to 16.
You can assign priority levels to each hand-held
transmitter, allowing the transmitter to arm the
system only, or to arm and disarm the system, for
example. Refer to Section 13.3 User Code Priority for
more information.
transmitters to operate only as User Codes 9 to 16.
You can assign priority levels to each hand-held
transmitter, allowing the transmitter to arm the
system only, or to arm and disarm the system, for
example. Refer to Section 13.3 User Code Priority for
more information.
Before a hand-held radio transmitter can operate the
control panel, you must teach the transmitter’s radio
code to the control panel. Refer to Section 4.3
Changing or Deleting Remote Radio User Codes for more
information.
control panel, you must teach the transmitter’s radio
code to the control panel. Refer to Section 4.3
Changing or Deleting Remote Radio User Codes for more
information.
4.3
Changing or Deleting Remote
Radio User Codes
Radio User Codes
You can use up to eight remote radio hand-held
transmitters (User Codes 9 to 16) to operate the
system. Before the control panel accepts a signal
from a remote radio hand-held transmitter, the
control panel must learn the transmitter’s code.
transmitters (User Codes 9 to 16) to operate the
system. Before the control panel accepts a signal
from a remote radio hand-held transmitter, the
control panel must learn the transmitter’s code.
You can substitute the Installer Code for
the Master Code below to change or
delete remote radio User Codes.
the Master Code below to change or
delete remote radio User Codes.
To add or change a remote radio User Code:
1. Enter the Master Code and press [1][AWAY].
1. Enter the Master Code and press [1][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Enter the user number (9 to 16) you want to add
or change and press [AWAY].
Two beeps sound and the corresponding zone
indicators light. Refer to Table 18 on page 21.
Two beeps sound and the corresponding zone
indicators light. Refer to Table 18 on page 21.
Table 18: Codepad Indicators for Remote Radio
User Numbers
Data
Zone Indicators
Value
1
2
3
4
5
6
7
8
MAINS
9
X X
10
X
11
X
X
12
X
X
13
X
X
14
X
X
15
X
X
16
X
X
3. Enter the nine-digit RF ID number located on
the back of the hand-held transmitter and press
[AWAY].
Two beeps sound and the STAY and AWAY
indicators are extinguished.
[AWAY].
Two beeps sound and the STAY and AWAY
indicators are extinguished.
4. Repeat Steps 1 to 3 to add or change another
remote radio User Code.
This function is automatically terminated if
you do not press a button within 60 sec
or if you press [AWAY].
you do not press a button within 60 sec
or if you press [AWAY].
One long beep indicates that the code
already exists or you selected an incorrect
user number.
already exists or you selected an incorrect
user number.
When using a partitioned ICP-CC488
Control Panel, you must allocate the
remote radio User Codes to one or more
areas (refer to Section 19.5 User Code
Allocations).
Control Panel, you must allocate the
remote radio User Codes to one or more
areas (refer to Section 19.5 User Code
Allocations).