Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 5.0
System Functions
EN | 23
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
Example
To program RF wireless device number 3 whose 9-
digit ID number is 000094946, enter
digit ID number is 000094946, enter
[1 2 3 4 0][AWAY][3][AWAY]
[0 0 0 0 9 4 9 4 6][AWAY]
[0 0 0 0 9 4 9 4 6][AWAY]
To delete an RF wireless device:
1. Enter the Installer Code and press [0][AWAY].
1. Enter the Installer Code and press [0][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Enter the RF device number (1 to 16) you want
to delete and press [AWAY].
Two beeps sound and the corresponding
codepad indicators light to show the RF device
number you selected.
Two beeps sound and the corresponding
codepad indicators light to show the RF device
number you selected.
3. Press [STAY] to delete the RF device.
Two beeps sound and the STAY and AWAY
indicators are extinguished.
indicators are extinguished.
4. Repeat Steps 1 to 3 to delete another RF wireless
device.
5.1.2
Set the Number of Days until the First
Test Report
Test Report
This function determines when the system sends the
first Test Report (Contact ID Event Code 602). If you
do not use this Installer Code function, the first Test
Report is sent to the base station receiver after the
repeat interval programmed in Location 428 (refer to
Section 15.28 Test Reporting Time). If you want the
system to send the first Test Report sooner than the
repeat interval, use this function to set when the first
Test Report is sent.
first Test Report (Contact ID Event Code 602). If you
do not use this Installer Code function, the first Test
Report is sent to the base station receiver after the
repeat interval programmed in Location 428 (refer to
Section 15.28 Test Reporting Time). If you want the
system to send the first Test Report sooner than the
repeat interval, use this function to set when the first
Test Report is sent.
To set the first Test Report:
1. Enter the Installer Code and press [1][AWAY].
1. Enter the Installer Code and press [1][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Enter the number of days (1 to 15) until the first
Test Report is sent and press [AWAY].
Two beeps sound and the STAY and AWAY
indicators are extinguished. The system returns
to the disarmed state.
Two beeps sound and the STAY and AWAY
indicators are extinguished. The system returns
to the disarmed state.
Each time you enter Installer’s
Programming Mode, the first Test Report
time defaults back to the repeat interval
set in Location 434.
Programming Mode, the first Test Report
time defaults back to the repeat interval
set in Location 434.
The number of days decrements by one at
2400 hours as set in Locations 901 to
904 (refer to Section 17.16 System
Time).
2400 hours as set in Locations 901 to
904 (refer to Section 17.16 System
Time).
Example
If the repeat interval is set to 7 days, but you want
the first Test Report to be sent in 2 days, enter:
the first Test Report to be sent in 2 days, enter:
[1 2 3 4 1][AWAY][2][AWAY]
5.1.3
Change Domestic Phone Numbers
When the system is set up for domestic dialing, this
function allows the installer to view and program the
telephone numbers the system calls if an alarm
occurs. Refer to Section 9.0 Domestic Dialing on page
42 for more information.
function allows the installer to view and program the
telephone numbers the system calls if an alarm
occurs. Refer to Section 9.0 Domestic Dialing on page
42 for more information.
To change domestic phone numbers:
1. Enter the Installer Code and press [2][AWAY].
1. Enter the Installer Code and press [2][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
If no telephone numbers are programmed, they
are displayed one digit at a time using the remote
codepad indicators. Refer to Table 21 on page 24
for the indicators and their meanings.
If no telephone numbers are programmed, an
additional two beeps sound after entering this
mode. These two beeps normally sound after
you enter the last digit of the last phone number.
indicators flash.
If no telephone numbers are programmed, they
are displayed one digit at a time using the remote
codepad indicators. Refer to Table 21 on page 24
for the indicators and their meanings.
If no telephone numbers are programmed, an
additional two beeps sound after entering this
mode. These two beeps normally sound after
you enter the last digit of the last phone number.
2. Enter the first phone number.
Each digit is displayed as you enter it.
3. If you are programming another phone number,
press [STAY][4] to separate the end of one
phone number and the beginning of the next.
If you are not programming other numbers, go
to Step 5.
phone number and the beginning of the next.
If you are not programming other numbers, go
to Step 5.
4. Repeat Steps 2 and 3 to program another phone
number.
5. Press [AWAY] to exit from this mode.
Table 20: Domestic Dialing Digits
Digit
Required
Required
Number to
Program
Program
Digit
Required
Required
Number to
Program
Program
0 0 8 8
1 1 9 9
2 2
3 3 *
[STAY]1
4 4 # [STAY]2
5
5
4 sec pause
[STAY]3
6 6 break
[STAY]4
7 7 15 [STAY]5
Example
If you want to program two separate telephone
numbers (9672 1777 and 9672 1233), enter:
numbers (9672 1777 and 9672 1233), enter:
[1 2 3 4 2][AWAY][9 6 7 2 1 7 7 7][STAY]
[4 9 6 7 2 1 2 3 3][[AWAY]
[4 9 6 7 2 1 2 3 3][[AWAY]
You can suspend domestic dialing at any time (for
example, you are moving house and do not want the
system to continue calling your work place or mobile
phone).
example, you are moving house and do not want the
system to continue calling your work place or mobile
phone).
To disable domestic dialing:
Enter the Installer Code and press [2][AWAY]
[STAY][4][AWAY].
[STAY][4][AWAY].