Bosch FMR-7036 User Manual
FMR-7036 | Fire Annunciator Keypad | 5.0
Setting the FMR-7036 Address
4
Bosch Security Systems, Inc. | 9/08 | F01U010584-01
Figure 3:
Mounting Hole Locations
Back of FMR-7036 Keypad
1
2
2
3
3
3
3
4
1 - Holding tabs for reference guides
2 - Release tab
3 - Mounting Hole
4 - Wire Entrance
Do not secure the base at this point.
Figure 4:
Inside View of FMR-7036 Keypad
1
8
Green
Yellow
Yellow
Black
Red
Connector Cable Orientation
1
2
3
4
5
3
6
7
8
1 - Wire Entrance
2 - Internal Sounder
3 - Mounting Hole
4 - Address jumper pins
5 - Control Keys
6 - Reset switch
7 - 2-line 16-character display
8 - Lock
5.0 Setting the FMR-7036
Address
Each keypad must have its address set
with its address pins. The keypads must
also be programmed at the control panel.
with its address pins. The keypads must
also be programmed at the control panel.
Figure 5:
FMR-7036 Address Jumper Settings
Address 1
Address 4
Address 7
Address 10
Address 13
Address 2
Address 5
Address 8
Address 11
Address 14
Address 3
Address 6
Address 9
Address 12
Do not use
address 15
address 15
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
1 2
4
8
3
5 6 7
Select the keypad address (1-14).
Place the shorting jumpers over the address pins as
shown in Figure 5.
shown in Figure 5.
Each option bus device must have its own
address, and each address can only
support one device.
address, and each address can only
support one device.
6.0 Wiring the FMR-7036
Be sure all wiring is un-powered before
routing. Keypad wiring cannot be run with
smoke detector wiring, NAC wiring or MUX
loop wiring.
routing. Keypad wiring cannot be run with
smoke detector wiring, NAC wiring or MUX
loop wiring.
For the FPD-7024 FACP, the maximum allowed DC
current draw from the auxiliary power is 500 mA for
keypads. The maximum length of wire (all branches
added together) that can be connected to the option
bus terminals is 4000 ft (1,219 m).
current draw from the auxiliary power is 500 mA for
keypads. The maximum length of wire (all branches
added together) that can be connected to the option
bus terminals is 4000 ft (1,219 m).
The maximum length between any one device and
the panel terminals depends on the current drawn
on the branch that the device is on. The current
draw on a particular branch can be found by adding
together the individual current draws of each device
connected to the branch.
the panel terminals depends on the current drawn
on the branch that the device is on. The current
draw on a particular branch can be found by adding
together the individual current draws of each device
connected to the branch.
Refer to the FPD-7024 Installation Guide
(P/N: F01U008458) for detailed wire length
calculations.
(P/N: F01U008458) for detailed wire length
calculations.