Bosch 9 6 BLCC110U User Manual
Solution 64
14
Bosch Security Systems 09/06 BLCC110U
User Guide
Main Office A001
Disarmed
Disarmed
Press OK or MENU
If the area is turned All On, the keypad will display:
Main Office A001
Armed All On
Armed All On
If the area is turned Part On, the keypad will display:
Main Office A001
Armed Part On
Armed Part On
3. To exit, press [OK].
Areas > Commands >
Turn Area On/Off
MENU 2-0-1
This menu allows you to turn an area All On or off.
Enter programming mode (PIN + MENU) then,
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [1].
A list of different areas will display on the keypad.
A001 Reception Area
A002 Sales Dept
A003 Administration Dept
A003 Administration Dept
Press
, OK or MENU
If an area has already been turned All On or Part On, a
‘tick’ () will be displayed on the right side of the name
description (see A002 Sales Dept above).
‘tick’ () will be displayed on the right side of the name
description (see A002 Sales Dept above).
2. Use the [
↑] and [↓] keys to select the area that you want
to turn on or off, then press [OK] to select. Alternatively,
you can enter the area number you want to turn on or off,
then press [OK].
you can enter the area number you want to turn on or off,
then press [OK].
Areas > Commands >
Turn All Areas On
MENU 2-0-2
This menu allows you to turn on all areas that your PIN has been
assigned to at the same time All On. The keypad display below
shows the area icons 1 through to 8.
Enter programming mode (PIN + MENU) then,
assigned to at the same time All On. The keypad display below
shows the area icons 1 through to 8.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [2].
The keypad will display the exit time bar to prompt you
to exit all areas. You should leave all areas now.
to exit all areas. You should leave all areas now.
Area 1 Name
EXIT NOW
When exit time has expired, the keypad will display that
all areas are turned All On (Armed).
all areas are turned All On (Armed).
Area 1 Name
ARMED
Fri,Aug,13 5:34 pm
i
Note
Area icons will only display if programmed to
do so by your security installer.
Areas > Commands >
Turn All Areas Off
MENU 2-0-3
This menu allows you to turn off all areas that your PIN has been
assigned to at the same time. However, this menu requires at
least one area that has a keypad assigned to it to be disarmed
before you can access this command.
Enter programming mode (PIN + MENU) then,
assigned to at the same time. However, this menu requires at
least one area that has a keypad assigned to it to be disarmed
before you can access this command.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [3].
Areas > Commands >
Move To Area
MENU 2-0-4
This menu allows you to operate multiple areas from the same
keypad when the system has been partitioned. Before operating
a different area, you will need to move the keypad to the area
that you want to operate.
Enter programming mode (PIN + MENU) then,
keypad when the system has been partitioned. Before operating
a different area, you will need to move the keypad to the area
that you want to operate.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [4].
A list of different areas will display on the keypad.
A001 Reception Area
A002 Sales Dept
A003 Administration Dept
A003 Administration Dept
Press
, OK or MENU
2. Use the [
↑] and [↓] keys to select the area that you want
to move the keypad display to, then press [OK] to select.
Alternatively, you can enter the area number that you
want to move the keypad display to, then press [OK].
Alternatively, you can enter the area number that you
want to move the keypad display to, then press [OK].