Wayne-Dalton AND 9600 User Manual
43
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer section online at www.Wayne-Dalton.com
Trolley Installation for
low headroom
❉
HIGH aRC
lOW
HEaDROOM
TRaCk
TOP
sECTION
lEVEl
FIg. 3.1
FIg. 3.2
FIg. 3.3
sTRaIGHT
aRM
FIg. 3.4
CuRVED
aRM
CuT sTRaIGHT
aRM TO
aCCOMPlIsH
TROllEy
sETTING
OPERATOR hOOk-UP ChART FOR lOW hEADROOM
OPERaTOR MODEls
TyPE Of aRM BEING usED
PREfERRED
HOOkuP
REf. IllusTRa-
TIONs aBOVE
OPTIONal
HOOkuP
REf. IllusTRaTIONs
aBOVE
Quantum/ClassiC
CurveD /
straight
FIg. 3.4
straight
FIg. 3.3
linear
straight
FIg. 3.3
n/a
N/A
liftmaster
(sears)
CurveD /
straight
FIg. 3.4
straight
FIg. 3.3
genie
CurveD /
straight
FIg. 3.4
straight
FIg. 3.3
Determine center line of door. Mark vertical line at this
point, on the header wall. Raise the door slightly until the
top section reaches the highest point of travel (high arc)
point, on the header wall. Raise the door slightly until the
top section reaches the highest point of travel (high arc)
.
using a level, mark this high arc point of travel on the header
wall
wall
, intersecting the vertical center line, as shown in fIG.
3.1 through 3.2.
Hold the wall bracket’s bottom edge to the
appropriate 1/2” - 1” (room permitting) above of the high
arc line and centered on the vertical line
arc line and centered on the vertical line
, as shown in fIG.
3.2
. spot the wall brackets mounting holes on the header
wall and then refer to your
garage door operator manual for
pre-drilling and securing the
wall bracket to header.
using the
OPERaTOR HOOk-uP CHaRTs, refer to referenced illustrations
in fIG. 3.3 through fIG. 3.4 for correct arm hook-up from
trolley to operator bracket.
in fIG. 3.3 through fIG. 3.4 for correct arm hook-up from
trolley to operator bracket.
NOTE: Refer to your operator manual for specific details on
how to assembly the curved and straight arm, as shown in
fIG. 3.3 through fIG. 3.4.
how to assembly the curved and straight arm, as shown in
fIG. 3.3 through fIG. 3.4.
NOTE: Depending on your setup, you may or may not have to
cut straight arm to accomplish trolley settings, as shown in
fIG. 3.3 through fIG. 3.4.
cut straight arm to accomplish trolley settings, as shown in
fIG. 3.3 through fIG. 3.4.
align hole in the appropriate arm with holes in operator
bracket tabs, as shown in
bracket tabs, as shown in
FIg. 3.5. Insert 5/16” x 1-1/4”
clevis pin, making sure hole in clevis pin is outside of second
tab of operator bracket. Insert hairpin cotter into clevis pin
hole and spread hairpin cotter to ensure it will secure
assembly, as shown in
tab of operator bracket. Insert hairpin cotter into clevis pin
hole and spread hairpin cotter to ensure it will secure
assembly, as shown in
FIg. 3.5.
fROM
sTEP 12
sTEP 12
HIGH aRC
lINE
lINE
TyPICal 1/2” - 1”
aBOVE HIGH aRC
aBOVE HIGH aRC
VERTICal
CENTER lINE
CENTER lINE
HEaDER
TORquEMasTER
®
COuNTERBalaNCE
FIg. 5.2
hairpin
COtter
COtter
OperatOr
BraCket
DOOr
arm
5/16” x 1-1/4”
Clevis pin
OperatOr
BraCket taBs
DOOr arm
tOp vieW
hairpin COtter
(OutsiDe Of OperatOr
BraCket taB)
OperatOr BraCket taBs
FIg. 3.5
OPTIONA
l
INST
All
ATION