England's Stove Works 25-PDV User Manual
NOTE: Follow the same procedure to work on the bottom auger, with the exception that the
pellets do not have to be removed from the hopper.
pellets do not have to be removed from the hopper.
Convection Blower
The Convection (room air) Blower (Part #PU-4C447) is located on the left side of the unit
and can be removed by disconnecting the power leads and removing the four mounting
screws. Once this is done, the blower will slide out of the stove. This procedure can be
reversed to install a new blower.
and can be removed by disconnecting the power leads and removing the four mounting
screws. Once this is done, the blower will slide out of the stove. This procedure can be
reversed to install a new blower.
Combustion Blower
To clean or replace the Combustion (exhaust) Blower (Part #PU-076002B), the power
leads and the pellet vent pipe must be disconnected. Next, remove the screws that hold the
blower to the steel exhaust tube and slide the blower from the stove. The blower impeller,
blower tube and steel blower exhaust tube on the unit should be brushed and vacuumed.
When cleaning or replacing the blower a new gasket (Part # PU-CBG) should be added
between the blower flange and the steel exhaust tube.
leads and the pellet vent pipe must be disconnected. Next, remove the screws that hold the
blower to the steel exhaust tube and slide the blower from the stove. The blower impeller,
blower tube and steel blower exhaust tube on the unit should be brushed and vacuumed.
When cleaning or replacing the blower a new gasket (Part # PU-CBG) should be added
between the blower flange and the steel exhaust tube.
Vacuum Switch
This unit is equipped with Vacuum Shut Down Switches (Part # PU-VS and PU-VS-A),
which help control various functions of the unit. If an operational error occurs in the unit, a
switch will either stop the top (feed) auger or shut the unit off; if the unit turns off an E-1
Code (error code) will appear in the Heat Range and Blower Speed windows of the Control
Board. Situations which could cause this include power failure, Combustion Blower failure,
improper flue installation, a blocked flue (from rodents, nests, etc.), or “dirty burning” from
burning improper fuel (see “Important Information” at the beginning of the manual).
which help control various functions of the unit. If an operational error occurs in the unit, a
switch will either stop the top (feed) auger or shut the unit off; if the unit turns off an E-1
Code (error code) will appear in the Heat Range and Blower Speed windows of the Control
Board. Situations which could cause this include power failure, Combustion Blower failure,
improper flue installation, a blocked flue (from rodents, nests, etc.), or “dirty burning” from
burning improper fuel (see “Important Information” at the beginning of the manual).
Gaskets
IMPORTANT: IMPROPER GASKET MAINTENANCE, INCLUDING FAILURE TO
REPLACE GASKETS, CAN CAUSE AIR LEAKS RESULTING IN SMOKE-BACKS.
REPLACE GASKETS, CAN CAUSE AIR LEAKS RESULTING IN SMOKE-BACKS.
This unit comes with a 3/4” rope gasket around the door that should be replaced every
two years. To replace the door gasket (Part # AC-DGKC), the old gasket must first be
removed entirely — prior to adding the new adhesive, you may have to scrape the old
cement from the door channel. Once the cement and gasket have been added, the door
should be closed and latched for twenty-four hours to allow the cement to harden.
removed entirely — prior to adding the new adhesive, you may have to scrape the old
cement from the door channel. Once the cement and gasket have been added, the door
should be closed and latched for twenty-four hours to allow the cement to harden.
If you are replacing the window gasket (Part #AC-GGK), the new gasket will already
have adhesive on one side. Remove the paper on the adhesive side and place the gasket
around the outside edge of the glass by forming a “U” with your fingers and placing the
gasket around the glass. You should also replace the Combustion Blower gasket (Part #
PU-CBG) whenever you remove or clean the Combustion Blower.
around the outside edge of the glass by forming a “U” with your fingers and placing the
gasket around the glass. You should also replace the Combustion Blower gasket (Part #
PU-CBG) whenever you remove or clean the Combustion Blower.
Finish
This new unit has been painted with High-Temperature Paint that should retain its
original look for years. If the unit should get wet and rust spots appear, the spots can be
sanded with plain steel wool and repainted. We recommend this paint, as others may not
adhere to the surface or withstand the high temperatures.
original look for years. If the unit should get wet and rust spots appear, the spots can be
sanded with plain steel wool and repainted. We recommend this paint, as others may not
adhere to the surface or withstand the high temperatures.
Glass
This unit has a 9” x 9” ceramic glass (Part #AC-G9, comes with gasket) in the viewing
door. Surface scratches are acceptable and normal, but if this glass becomes cracked in
any area, the unit should be shut down and the window replaced with this high-temperature
ceramic glass.
door. Surface scratches are acceptable and normal, but if this glass becomes cracked in
any area, the unit should be shut down and the window replaced with this high-temperature
ceramic glass.