Sony MKE-9040M User Manual
1-18
MVE-9000 IM
D3704 (H-2) : SYSTEM status LED
Lit when configuration is complete and FPGA reset is also
complete. If the LED does not light, the FPGA may be
defective.
Lit when configuration is complete and FPGA reset is also
complete. If the LED does not light, the FPGA may be
defective.
D3705 (H-5) : CN EXIST status LED
CN-2357 board presence/absence status indication.
Lit on the DVP-24A board that is installed in the same slot
of CN-2357 board when CN-2357 board is present.
CN-2357 board presence/absence status indication.
Lit on the DVP-24A board that is installed in the same slot
of CN-2357 board when CN-2357 board is present.
D3706 (H-6) : CN POWER status LED
The CN-2357 board power status indication.
Lit on the DVP-24A board that is installed in the same slot
of CN-2357 board while the power supply inside the CN-
2357 board is activated.
The CN-2357 board power status indication.
Lit on the DVP-24A board that is installed in the same slot
of CN-2357 board while the power supply inside the CN-
2357 board is activated.
D3801 (H-1) : DBG 7 A status LED
Used for design purpose.
Used for design purpose.
D3802 (H-1) : DBG 6 A status LED
Used for design purpose.
Used for design purpose.
D3803 (H-1) : DBG 5 A status LED
Used for design purpose.
Used for design purpose.
D3804 (H-1) : DBG 4 A status LED
Used for design purpose.
Used for design purpose.
D3901 (H-6) : DBG 7 B status LED
Used for design purpose.
Used for design purpose.
D3902 (H-6) : DBG 6 B status LED
Used for design purpose.
Used for design purpose.
D3903 (H-7) : DBG 5 B status LED
Used for design purpose.
Used for design purpose.
D3904 (H-7) : DBG 4 B status LED
Used for design purpose.
Used for design purpose.
ND3801 (H-2), ND3802 (H-2) : STATUS A LED
DVP-24A board CPU_A status indication.
DVP-24A board CPU_A status indication.
ND3901 (H-6), ND3902 (H-6) : STATUS B LED
DVP-24A board CPU_B status indication.
DVP-24A board CPU_B status indication.
<Switch>
S3501 (H-3) : CPU A CONFIG switch
Used for maintenance purpose.
S3501 (H-3) : CPU A CONFIG switch
Used for maintenance purpose.
S3601 (H-3) : CPU B CONFIG switch
Used for maintenance purpose.
Used for maintenance purpose.
S3801 (H-2) : SETUP A switch
Used for maintenance purpose.
Used for maintenance purpose.
S3901 (H-5) : SETUP B switch
Used for maintenance purpose.
Used for maintenance purpose.
<Connector>
CN3502 (H-4) : USB A terminal
Used for maintenance purpose.
CN3502 (H-4) : USB A terminal
Used for maintenance purpose.
CN3503 (H-3) : COM A terminal
Used for maintenance purpose.
Used for maintenance purpose.
CN3602 (H-3) : COM B terminal
Used for maintenance purpose.
Used for maintenance purpose.
CN4301 (H-4) : EPR terminal
Used for maintenance purpose.
Used for maintenance purpose.
CN4601 (H-3) : IEEE1394 terminal
Used for maintenance purpose.
Used for maintenance purpose.
<TEST terminal>
E201 (B-7), E202 (D-7), E301 (C-7), E302 (F-7),
E401 (G-7), E501 (H-5) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
E201 (B-7), E202 (D-7), E301 (C-7), E302 (F-7),
E401 (G-7), E501 (H-5) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP201 (B-7) :
+
+
+
+
+1.5 V-1/20 A check terminal
+1.5 V-1/20 A measuring terminal.
TP202 (D-7) :
+
+
+
+
+1.5 V-2/20 A check terminal
+1.5 V-2/20 A measuring terminal.
TP301 (C-7) :
+
+
+
+
+2.5 V-1/20 A check terminal
+2.5 V-1/20 A measuring terminal.
TP302 (F-7) :
+
+
+
+
+2.5 V-2/20 A check terminal
+2.5 V-2/20 A measuring terminal.
TP401 (G-7) :
+
+
+
+
+3.3 V/20 A check terminal
+3.3 V/20 A measuring terminal.