American Standard 2881 User Manual
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
SPREAD
LAVATORY
FAUCET
LAVATORY
FAUCET
Installation
Instructions
M 9 6 8 2 1 1
Certified to comply with ANSI A112.18.1M
1
SPOUT ASSEMBLY
4
2
6
1
3
VALVE INSTALLATION
2
5/16'' MIN.
Insert VALVE BODY (1) through hole from underside
of SINK (2). Threads of VALVE BODY (1) should extend
at least 5/16 inch above SINK (2) top. If necessary,
adjust LOCKNUT (3). Make sure RUBBER WASHER (6)
is installed.
of SINK (2). Threads of VALVE BODY (1) should extend
at least 5/16 inch above SINK (2) top. If necessary,
adjust LOCKNUT (3). Make sure RUBBER WASHER (6)
is installed.
Place RUBBER RING (4) on SINK (2) and screw DECK
ADAPTER (5) onto VALVE BODY (1) until snug against
internal stop.
ADAPTER (5) onto VALVE BODY (1) until snug against
internal stop.
Set VALVE BODIES (1,1A) so that their outlets are
facing toward center of sink and then tighten LOCKNUT
(3) using WRENCH (7) supplied with faucet.
facing toward center of sink and then tighten LOCKNUT
(3) using WRENCH (7) supplied with faucet.
7
3
TEE AND HOSE INSTALLATION
2881
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.
instructions carefully before you begin.
Connect TEE (1) to SPOUT SHANK (2). Tighten COUPLING
NUT (3).
NUT (3).
Connect COUPLING NUTS (4) of HOSE to each valve outlet and
tighten securely.
tighten securely.
1
3
2
4
HOSE
Insert SPOUT SHANK (1) through center
hole of SINK (2). Make sure RING
WASHER (3) is properly positioned
into SPOUT BASE.
hole of SINK (2). Make sure RING
WASHER (3) is properly positioned
into SPOUT BASE.
Assemble RUBBER WASHER (4),
BRASS WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of SINK (2).
BRASS WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of SINK (2).
Insert LIFT ROD (7) through SPOUT (8)
and slot of BRASS WASHER (5).
and slot of BRASS WASHER (5).
Align SPOUT (8) and tighten LOCKNUT (6).
Be sure slot in BRASS WASHER (5) is
positioned to the rear as shown.
Be sure slot in BRASS WASHER (5) is
positioned to the rear as shown.
7
8
1
3
4
6
5
SLOT
2
5
Turn off hot and cold water supplies before beginning.
CAUTION
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 2
© A m e r i c a n S t a n d a r d I n c . 2 0 0 2
by
C O L L E C T I O N
™
“
”
T H E
VALVE
OUTLET
OUTLET